A beam with a width b=300mm has loads w=35 kN/m and P-13 kN. If the allowable bending stress is Fb312.5 MPa, calculate the required height, h of the beam in mm. Round off final answer to the next integer (i.e. 358, 324, 421, etc.) P (kN) w (kN/m) Section 5.1m 4.2m

A beam with a width b=300mm has loads w=35 kN/m and P-13 kN. If the allowable bending stress is Fb312.5 MPa, calculate the required height, h of the beam in mm. Round off final answer to the next integer (i.e. 358, 324, 421, etc.) P (kN) w (kN/m) Section 5.1m 4.2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 5 cmx12 cmx6 m wooden plank (S.G.wood = 0.70) is required to stand vertically in water. To reduce ...

A: We have to determine the value of draft of the wooden plank and metacentric height of the whole syst...

Q: Structural steel beams are to be placed at 7 ft 6 in on center under a reinforced concrete floor sla...

A: Step 1: Spacing= 7 ft 6 inch DL= 64 psf of floor area LL = 100 psf floor area Factored uniform load ...

Q: Two small circular orifices of diameters d, and d,, respectively, are placed on the side of a tank a...

Q: The number of accidents for 6 years recorded in a certain intersection is 5834. If the average daily...

A: Given data, Time period in years (N) = 6 Length in miles. = 1 Number of accident during period of ...

Q: Given a system as shown in the following figure. Calculate the water level difference between two ta...

A: Given, Pipe length (L) = 15 m Diameter (D) = 30mm or 0.03m Volume flow rate (V˙) = 1 m3/h or 0.00027...

Q: The 'Euler' load for a column is 1000 kN and crushing load is 1500 kN. The 'Rankine' load is equal t...

Q: 1. The floor crane is used to lift 600-kg concrete pipe. Determine the resultant internal loading on...

A: We have to determine the resultant internal loading on the cross section at H as per the given data ...

Q: An ascending grade of 4.84% meets a descending grade of -5.71% which serves as tangents for a parabo...

A: N1=4.84% N2=-5.71% SSD=100m To find length of curve

Q: rigid pavement is to be used to carry a wheel load of 58.77 kN. Enough dowels will be used across th...

A: Load=58.77kN Stress=1.45MPa

Q: uation, dete 1=3,000 in

Q: Determine the correct length of the line if 10:6

A: SURVEYING:

Q: A rigid pavement is to be used to carry a wheel load of 57.62 kN. Enough dowels will be used across ...

A: Load=57.62kN Stress=1.32MPa

Q: In a particular material, if the modulus of rigidity is equal to the bulk modulus, then the Poisson'...

Q: determine the accident rate. If the number of accidents for 7 years recorded in a certain intersecti...

A: Accident rate = Number of accidents / (ADT * N *365 ) Lets find the accident rate per HMVM for 100 ...

Q: :The formula used to compute 3OHV contains a factor Equals to 0.15 O 0.17 O 0.16 O

Q: In a falling-head permeability test, the time taken for the head to fall from 27 cm to 3 cm is 10 mi...

Q: For the structure shown below calculate the tension force in the lateral resisting system. Assume a ...

A: Assuming there is a structure, there will be a frame in the construction more often than not. Outlin...

Q: Load-Shear and Shear-Moment Relationships Requirements 1A. Reactions at the supports 1B. Shear diagr...

A: RA + RC = 40 + 16X3 RA + RC = 88 Moment diagram 40 x 1 +15 - 16 x 3 x 4.5 + Rc x 5 =0 Rc = 32.2 k...

Q: SITUATION 3: A 12-m simply supported bridge is constructed with 100-mm concrete slab deck supported ...

A: Shear Force: The algebraic sum of all the forces acting on the given beam or a structure at differen...

Q: Compute the maximum combined loads USING THE RECOMMENDED ASD EXPRESSIONS FROM THE AISC. (KEY ANSWER:...

A: Given data : D= 9000 lb L= 5000 lb Lr= 2500 lb E= ±6500 lb

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as s...

Q: Given data : Degree of saturation3D0.45 Void ratio=0.25 Specific gravity3D2.7 Find water content

A: This question is related with geotechnical engineering . In this question we are provided with value...

Q: A horizontal impervious floor of length 20 m is provided with a sheet pile of 5 m depth at its downs...

Q: ascending grade of 4.42% meets a descending grade of -5.45% which serves as tangents for a parabolic...

Q: Define, derive and give 2 examples of Green-Ampt Model.

Q: 3. Solve the a) slope at C and b) deflection at B using either AMM or DIM. Use of direct formulas no...

Q: Given a system as shown in the following figure. Calculate the water level difference between two ta...

A: Solution- The given values are as follows,Taking tannk (1) is the upper tank and tank (2) is lower ...

Q: Write the shear force and bending moment equations at each segment of the beam shown. Draw the V and...

Q: Suppose that a certain radioactive substance has a halflife of 34 years. If there are presently 7006...

A: Radioactive substances are atoms that decay naturally. They can give off alpha particles, beta parti...

Q: A determinate frame carries a concentrated and distributed load as shown in the figure. Determine th...

Q: Compute the peak hour factor if the hourly volume of traffic is 1978 veh/hour and the highest 15-min...

A: Given data, Hourly volume of traffic = 1978 veh/hr Peak 15 min volume = 780 vehicle To find out th...

Q: In the following case zero overland flow occurred. Gross rainfall on a 1 hectare hillslope occurred ...

A: To determine the volume of precipitation intercepted by the vegetation. Given, Area of the hillslo...

Q: Explain the difference between serpentine and helical scan recording.

Q: distributed load, Ao, is applied at the ground surface, what is the settlement of the clay layer cau...

Q: If water is flowing through a pipe of 5 cm diameter under a pressure of 20 N/cm2 and a mean velocity...

A: Given data: Diameter, d = 5 cm Pressure, P = 20 Ncm2 Mean velocity, v = 2 ms

Q: A fold-down shelf opens up and is supported by a rope attached between points A and B. What is the t...

Q: Find the area of the region between the curves y = x^3, y = -x, and y = 1. Round off to two decimal ...

Q: Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1) ...

A: Resultant force: The total number of forces acting at a point or the system with magnitude and direc...

Q: Given data: Degree of saturation%3D0.45 Void ratio=0.25 Specific gravity%=D2.7 Find water content

Q: The levelling staff held at a distance of 200 m is read at 4.54 m with the bubble out of centre by 2...

Q: eompressed by a free an elliptical seetion wntil its inside huight is 18cma Deteusne the lydoculíe m...

Q: f static indeterminacy

Q: The square footing shown in the figure carries a load of 3500 kN. Assume that the stress below the f...

A: As per Bartleby policy i can answer only one question at a time. Please upload other questions agai...

Q: Urban arterial flow

A: Transportation engineering:

Q: small funnel in the shape of a cone is being emptied of fluid at the rate of 14 cubic centimeters pe...

Q: Determine degree of static indeterminacy

Q: A 5 cmx12 cmx6 m wooden plank (S.G.wood = 0.70) is required to stand vertically in water. To reduce ...

Q: In a particular material, if the modulus of rigidity is equal to the bulk modulus, then the Poisson'...

Q: and frames. E and I are constant unless noted otherwise. The force For Problems 11.17 through 11.22,...

Q: kg car that t 003x2. If the consta e x-component of th total force (KN). of line

Question

A beam with a width b=300mm has loads w=35 kN/m and P=13
kN. If the allowable bending stress is Fb312.5 MPa, calculate the
required height, h of the beam in mm.
Round off final answer to the next integer (i.e. 358, 324, 421, etc.)
P (kN)
w (kN/m)
Section
5.1m
4.2m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
A simply supported beam is used to carry the uniformly distributed load of magnitude 3 W and the concentrated load W. What is the maximum allowable value of W if the working stress in bending is 122 MPa? b = 180; d = 318 Round your answers to 2 decimal places.
05. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in the Figure Q5. Given that E=2x10"N/m, A=10mm, L=Im and P-lkN. The horizontal displacement of Joint C (in mm, up to one decimal place) is „JointC P 2AE 7. AE AE Figure 05
An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t Y ▼ 2 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response: 318.329 mm 290.593 mm 355.903 mm 263.312 mm
4.15 The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. La 15 mm 40 mm 20 mm 粗眼 d = 30 mm M R Fi
es A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, F Ra 1 X Y 12 Determine the section modulus of the beam. Select the correct response: 72113.831 mm³ 87833.695 mm³ 57962.384 mm3 45378.561 mm³ Ri 12
A circular beam carries a concentrated and a distributed load as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPA and the maximum shear is 508.4kN. USE ANY METHOD Let, P=190KN, a=2m, b=1m and c=3m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P 5w 2w A B a b b If the deflection at the free end (leftmost part of the beam) is equal to -51.476603223441mm, Determine the radius of the cross-section of the circular beam. Determine the slope at the free end of the beam (in degrees).
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1700 N, T = 4167 Nm, a = 0.94 m, b = 1.07 m, c = 0.98 m, w = 33 mm, and h = 79 mm . Round off the final answer to one decimal place. P T W Y U A/O А h B k a b C C | 1 D
An 8 m simple beam is loaded with a 208 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t = 20 mm с C Y 12 If c = 333.33 mm, what is maximum stress the beam is subjected to? Select the correct response: 228.000 MPa 152.000 MPa 166.400 MPa O 124.800 MPa
A simple beam 4.4 m in span carries a concentrated load of 316 kN at its midspan and is subjected to an axial tensile force of 243 kN. Fy = 248 MPa.Three sections are being considered as follows with their corresponding properties relevant to the problem.Use the formula: (fa/0.60Fy) + (fb/0.66Fy) <1.0 Questions:What is the lowest axial Stress?Hint Answer: 18.69
L For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 17 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm tf = 20 mm tw = 15 mm %3D b tw O bending MPa Round to one decimal place
A beam with the cross-section shown is subjected to a vertical shear of 28 kN. Determine: (a) the largest shearing stress in that section, (b) the shearing stress at Point a. 65 mm a 100 mm 210 mm 8 mm 1 200 mm 8 mm T max = T@a= kPa kPa