A band brake embraces a 500 mm diameter drum with an angle of lap of 270° and produces a braking torque of 200 Nm. The coefficient of friction is 0.2. One end of the band is attached to the fulcrum pin and the other end is attached to a pin B. Which of the following is the tension in the slack side of the band? 75 -450 T₂ F 270⁰ O 280 N O 510N O 255 N 0445N All dimensions in mm.

A band brake embraces a 500 mm diameter drum with an angle of lap of 270° and produces a braking torque of 200 Nm. The coefficient of friction is 0.2. One end of the band is attached to the fulcrum pin and the other end is attached to a pin B. Which of the following is the tension in the slack side of the band? 75 -450 T₂ F 270⁰ O 280 N O 510N O 255 N 0445N All dimensions in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The torque transmitted by a single block brake is 70 N-m. The coefficient of friction between the drum and the lining is 0.35. The drum diameter is 240 mm. Which of the following is the normal force RN pressing the block on the brake block on the wheel? 200 200 4 TEL 200 N 560 N 1600 N 1450 N
Q1 Q5) Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm, load factor is 2 and the mean diameter to face width ratio is 6.
The figure shows an internal rim-type brake having an inside rim diameter of 300 mm and a dimension R 5 125 mm. The shoes have a face width of 40 mm and are both actuated by a force of 2.2 kN. The drum rotates clockwise. The mean coefficient of friction is 0.28. a. Find the maximum pressure and indicate the shoe on which it occurs. b. Estimate the braking torque effected by each shoe, and find the total braking torque. c. Estimate the resulting hinge-pin reactions. 30°- 30°. R 120° 120° Pin Pin 30° 30° Figure 3: An internal rim-type brake
Q5: The block brake, as shown, provides a braking torque of 360 N.m The diameter of the brake drum is 300 mm. The coefficient of friction is 0.3. Find 1. the force (P) to be applied at the end of the lever for the clockwise and counter clockwise rotation of the brake drum, and 2. The location of the pivot or fulcrum to make the brake self-locking for the clockwise rotation of the brake dracs 100 10 ( F₁ 4 μ sin 80 20+ sin20 T = (F₁) r Bearing Area A, b(2r sind) RN = (1 20 R 600 Brake drum
A single block brake, as shown, requires an operating force of 700 N. If the coefficient of friction between the drum and the lining is 0.3, which of the following is the tangential braking force F+? 50 440 N 315 N 510 N 200 670 N 125 250 -F₁ 700 N
Consider the arrangement of a simple band brake as shown in the figure. Determine the brake torque due to load applied at end A. Take the coefficient of friction as 0.22. 1.5 m 0.5 m B Answer Choices: a. 320 N-m b. 120 N-m c. 480 N-m d. 260 N-m 0.3 m 20% P = 250 N
The width of the simple band brake shown in the figure is 30 mm. The coefficient of friction between the brake and the drum surface is 0.20. Determine the braking torque and thickness of the band if the tensile stress is not to exceed 65 N/mm2.
SELF-CHECK EXERCISE PROBLEM 06. What force F must be exerted on the brake arm shown to hold the drum against rotation if P = 1000KN and the coefficient of belt friction is 0.30. Figure, F ¡A 800mm 450 B 200mm 100mm 200mm CI P=1000KN
+ Frictional Forces on Flat Belts When engineers design belt drives and band brakes, they engineer them to withstand the frictional forces that develop between the belts or bands and their contacting surfaces. These frictional forces lead to tensions on each side of the contacting surfaces that are unequal; the segment aligning with the motion of the belt or band has a greater tension. Figure B 0.500 m 0.200 m -0.400 m- A 3 of 3 0.300 m Part C mc= Block A has a mass of mA = 49.0 kg and rests on a flat surface. (Figure 3)The coefficient of static friction between the block and the surface is A = 0.300. The coefficient of static friction between the rope and the fixed peg B is 0.320. The width of the block is d = 0.250 m. Find the greatest mass, mc, that weight C can have such that block A does not move. Express your answer numerically in kilograms to three significant figures. ▸ View Available Hint(s) Submit Drouide Foodbook VAZO I vec ? 1 of 3 kg > Review
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is applied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Clockwise. 150 mm T 200 N 60 150 mm -675 mm 75 mm
The block brake shown below is set by a spring that produces a force S on each arm equal to 682 lb. The wheel diameter is 14 in., and the angle of contact for each block is 110°. Using 0.40 as a value of the coefficient of friction between the drum and lining, determine the maximum torque in foot-pounds that the brake is capable of absorbing. S + S 1/2" 1/2"
The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm² and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master cylinder cylinder Brake