a b C H Triple pole switch Balanced 3 phase load A balanced 3-phase load is supplied from a 3-phase supply. The contact in line c of the triple pole switch contactor fails to connect when switched on. If the line currents in lines a and b record 25A each, then the positive sequence component of the current is

a b C H Triple pole switch Balanced 3 phase load A balanced 3-phase load is supplied from a 3-phase supply. The contact in line c of the triple pole switch contactor fails to connect when switched on. If the line currents in lines a and b record 25A each, then the positive sequence component of the current is

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9MCQ: Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated...

See similar textbooks

Similar questions

Does an open- operation, the kVA rating compared to that of the original thr-phase bank is (a) 2/3 (b) 58 (c) 1
In a series AC resistive circuit: a) voltage leads current by 90°(degrees). O b) current leads voltage by 90°(degrees). © current and voltage are in phase. d) d current and voltage cancel.
Load sets are connected in series or in parallel but fuse must be always connected in a)series b)parallel c)connection d)non of them
In a three phase -four wire star connected system, the three outer wires are called as lines and the common wire in centre is called as to search hp
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
The one line diagram of the system and data: Gl and G2:reactance=0.2 p.u ,11kv, 100MVA T1 and T2: reactance =0.05p.u , 11/132 kv L1: reactance=0.216p.u, 132kv L2=0.09p.u, 132kv L3=0.09p.u, 132kv Calculate the fault current when a three phase fault accurs at bus 5 L2 L3 3. T2 4 T1 L1 -ter
The primary is 3000 turns, while the secondary is 6000 turns a. single-phase b. double-phase c. step-up d. step-down
Power output Step-up and down transformers lose 4% Full power potential (power input) Generator loses 15% Penstock loses 10% Channel Transmission loses 10% loses 5% Turbine loses 20% The overall losses in this system is Select one: O a. 55 % O b. 45 % O c. 50% O d. 64 %
Determine the DC currents (la. lc and I) and dc junction voltages (Var Ver and Vca) la-Blank 1 mA, le-Blank 2 mA, I-Blank 3 mA, Var Blank 4 V, Vcr Blank 5 V and VcB - Blank 6 V Use 2 decimal places. Use the following values. VBB= 3V RB= 5kOhms Rc=232 ohms Vcc =18 V BDC=65
E2(V) 120V Test Open-circuit Short- circuit Primary 12(A) .29A 2A P2(W) 8.78W 13.4W 6.85V E1(V) P1(W) 7.69W 13.14W Test Open-circuit Short- circuit 11(A) .62A SA 48V 2.83V Normal 12 at E1 11 P1 E2 12 P2 120V 50.6V 48.42V 48.8V 49.33V 182A 4A 6A 815A 1A 1.22A 142A .2 4.75A 237.4W 56.5W 120.3V 1.31A 1.77A 2.28A 2.73A 3.26А 3.74A 119.6V 119.8V 120.6V 119.4V 120.6V 120.1V 119.9V 120.3V 219.1W 48.3W 72.39W 98.3W 120.1W 146.9W .4 81.2W 108.2W 130.5W 159.2W 184W 209.2W 237.5W .8 49.1V 1.2 1.4 49.83V 49.91V 50.1V 50.55V 170W 193.6W 219.1W 238.1W 1.6 4.23A 1.616A 1.8 4.74A 1.82A 2.0 50.3V 5.18A 258.3W 119.1V 2A 1) Calculate the turns ratio from the transformer primary/secondary voltage ratinga a= Using the open-circuit data at the primary and the short-circuit data at the secondary, calculate the four transformer parameters (to 3 significant figures) and fill in the following table. Parameter Rel Value(ohm) Xel Rc1 Xm1 Using the open-circuit data at the secondary and the short-circuit data at…
4. A resistor and inductor are connected in parallel to a 277 volt, 60 Hz line. The resis- 12. tor has a current of 12 amperes flowing through it, and the inductor has a current flow of 8 amperes flowing through it. What is the total current flow in the circuit? m bas vlaqua
The figure shows the operation circuit of staircase wiring. What is the position of switches? C 120 O 12 C Phase Single Phase AC Supply 240V SOHz Two-Way Switch1 Two-Way Switch2 Lamp Neatr A. S1 is ON and S2 is ON B. S1 is OFF and S2 is ON C. S1 is OFF and S2 is OFF D. S1 is ON and S2 is OFF