a) A standard TTL inverter gate is shown in the figure. The supply voltage is 5V. Calculate theoutput voltage for both logic low and logic high input cases assuming input voltagesrespectively as 0.11V and 4.2V.Br= 130; BR = 0.24. You can make approximations when needed.Br = IcIs active region; BR = IE/ls inverse active regionb) Assume you connect a resistor of 1.8K to the output of the circuit when the output is at logichigh. What will be the change in the output voltage?1302R31.6k2R,4k2Input oT,OutputT,V,V.IkQR,

Solution (a) - When Vi =0.1 V Thus, when the input voltage is 0.1 V than output voltage is 4.28 V.

a) A standard TTL inverter gate is shown in the figure. The supply voltage is 5V. Calculate the output voltage for both logic low and logic high input cases assuming input voltages respectively as 0.11V and 4.2V. Br = 130; BR = 0.24. You can make approximations when needed. BF = Ic/Is active region; BR = I/IB inverse active region b) Assume you connect a resistor of 1.8K to the output of the circuit when the output is at logio high. What will be the change in the output voltage?

a) A standard TTL inverter gate is shown in the figure. The supply voltage is 5V. Calculate the output voltage for both logic low and logic high input cases assuming input voltages respectively as 0.11V and 4.2V. Br = 130; BR = 0.24. You can make approximations when needed. BF = Ic/Is active region; BR = I/IB inverse active region b) Assume you connect a resistor of 1.8K to the output of the circuit when the output is at logio high. What will be the change in the output voltage?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A certain digital circuits designed to operate with voltage levels of -0.2Vdc and -3.0Vdc. If H= 1 =-0.2 Vdc and L =0 =-3.0 Vdc, is this positive logic or negative logic ? H=+5.0Vdc. and. L=+1.0Vdc What are the voltage levels between fall and rise times are measured? What is the value of Duty cycle H if the waveform is high for 2 ms and low for 5 ms?
A single phase bridge inverter has an RLC load with R-20 ohm, L32 mit and C-0115 m The inverter frequency is to 60 H and DC input voltage is Vs 110V The average current of each transistor is equal to fontider up to the fifth harmonics in calculation Select on O None of these b 18A Oc 223A Od 6.JA
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition
Q4: Suggest a control gate drive circuit for a Triac, which is used to control a fan regulator. The gate signals should be synchronized with the input voltage. Draw the complete: 1. Circuit diagram with the load and 2. The waveform of the input and output voltages. ) Q.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In…
A full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vdc=100 V, R equals to 10 Ohm, and L equals 25 mH. The average current in the dc source is. Select one: O a. 52 A O b. None of the above O c. 4.41 A O d. 300 A
In an inverter circuit, the voltage value is equal to the input voltage value and the output voltage value. a.VIL b.VOL c.Vth d.VIH
A NOR gate has an input voltage Vcc equal to 5V. The input current is 2.2mA for high output and 3.5mA for low output. Find the power dissipated for 50% duty cycle.
The main function of the inverter is to convert the DC to AC waveforms Select one: a. True O b. False
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 2N and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .014 ,02 .01 Time (sec) .012 .016 .018 a. Find the RMS values of the load voltage and the load current b. Calculate and draw the voltage across the load inductance c. Calculate and draw the source current and find its average value
1. Voltage inputs to inverters that are between VIL and VIH are generally avoided. Why?
The output voltage of a single-phase full bridge voltage source inverter is controlled by unipolar PWM with one pulse per half cycle. For the fundamental rms component of output voltage to be 75% of DC voltage, the required pulse width in degrees (round off up to one decimal place) is
A single phase half bridge inverter is operating from a 25 V DC source and supplies power to resistive load. What is the distortion factor of fundamental output voltage?