A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters). (provide your answer with four decimal points)

A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters). (provide your answer with four decimal points)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a point in a pipe that lay flat ノ water in the pipe flows at a speed of 9.0 mls and has 6-40x 104 Pa a gaoge pressure is Find the gauge pressure at point 2 of pipe that lower than the first point 8.0 m and the cvoss - se ctional| area of the pipe is double of first point . Answer [1.52x105 Pa]
Q3/ A petroleum crude oil having a kinematics viscosity 0.0001 m²/s is flowing through the piping arrangement shown in the below Figure,The total mass flow rate is equal 10 kg/s entering in pipe (A) . The flow divides to three pipes ( B, C, D). The steel pipes are schedule 40 pipe. note that the dynamic viscosity 0.088 kg/m.s. Calculate the following using SI units: 1- The type of flow in pipe (A). 2- The mass velocity in pipe (B) GB. 3- The velocity in pipe (D) Up. 4- The Volumetric flow rate in pipe (D) QD. 5- The Volumetric flow rate in pipe (C) Qc. Oe = 2 o mm UB = 2UA Perralenm crude oL mic =? -> ma = 1o Kg/s = 50 mm Go 7000 K/m.s %3D Note that!. = 30 mm D: 0iameter, UIvelocity G mass velocity mass How ate.
G1/ In the fig.shown, the Flow rate Pipe (A) is equal ( QA = 25 Lit15), the diameter is equal ( DA = 75 mm, D, = De = Dc =30mm), and the velocity in Pipe (D) is equal (Uo=5 m/s), the relation between flow rate in in 6o mm, Pipe (B) and pipe (c) GB =3 Qc. Find the Value of '. Re, Qc, Qo. 2- UA, UB, Uc: Pe = 30 mm water Pc = 30mm imput QA = 25 2i+/sec OA= 75 mm = 6o mm input = A outPut = B, C, D accumulation = o.
For the following questions, Circle the correct answer Q1. We have a steady fully rough turbulent flow of water with constant density in a cylindrical pipe of constant diameter. The height of the uniform roughness elements in the pipe is k.. . . For a fully developed rough turbulent flow in the pipe, the condition ku. -> 70 is the same as k,> 66,. [True/False] V avg The wall shear stress T-pfU/8. It is applicable only for steady fully rough turbulent flow in the pipe. [True/False] The shear stress distribution is linear with the radial distance from the pipe centerline only for laminar flow. [True/False] The head loss per unit length is quadrupled when the discharge is doubled. [True/False] The piezometric pressure drops uniformly along the pipe because the flow is steady along the pipe [True/False]
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?
G1/ in the Pipe (A) is equal (PA= 25 Lit15), the diameter is equal ( DA - 75mm, Do = Fig.shown, the Flow rate in 6o mm, Dg = Dc%=30 mm), and the velocit Pipe (D) is equal (U0=5m/s), the relation between flow rate in Pipe (B) and pipe (c) %3D Find the Value af . 2- Un, UB, Uc. water Os = 30 mm input A QA - 25 Lit/sec = 75 mm fo mm %3D Inpud = A outPut = B,C,D accumule tion =o.
) where AP is the static The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP pressure drop measured over some length of pipe, L. Use the Hagen-Poiseuille equation and the Darcy-Weisbach equation to derive an expression for the fanning friction factor, f, for laminar flow through a circular pipe where Re is the Reynolds number. Choose one answer from the list below: of= of O None of the above 32 Re 16 Re O f = 64 Re = o f = 32μLc 3 d² 8 Re O f = 16 Re
Water flows through the pipe system as shown, mass flowrate A divides equally into B and C, and discharges to the atmosphere. 6 m/s 100 mm A 60 mm 60 mm 06 PROB_034 Cappri n n, Do the following: (A) Compute the mass flowrate at A, B and C (B) Compute the pressure in the pipe at A (C) Sketch the C.V. and FBD for the flow in the pipe section - label and identify all relevant components: coordinate directions, velocities, forces and/or pressures, inlet & outlet sections (D) Compute the x and y forces required to hold the pipe in the position shown
Q1/. A fan draws in air freely and discharges through a test duct of cross - section 0.07 m? in which the static pressure is 20 per cent of the velocity pressure . It the total efficiency of the tan is 65 percent and the input power is 1 kW , find the quantity of air being delivered in mə / min . ( Ans . 99 m' / min ]
As a process engineer, you are designing a new drinking water treatment plant using conventional treatment process including Two Rapid Mixers as follows: The design flow is 50 million gallons per day (MGD) (1 Gallon = 3.785 L, 1 m³ = 1000 L). The average temperature of water is 5°C with a dynamic viscosity, μ = 1.519 x 10-3 Pa.Sec In each rapid mixer with a square shape, detention time, e = 1 min, water depth H = 13 ft, and power input P = 1.5 kw (1 ft = 0.3048 m, 1 KW = 1,000 W) The equivalent diameter, TE for each rapid mixer is ________ m. TE || AIR 1) 4.1 2) 4.4 3) 4.6 4) 4.8 5) 0.4
On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
Take the density and dynamics viscosity of the water as follows, determine the value of friction factor (f), head loss (h1), pressure drop (dP) and power required to overcome the pressure drop (W) for the cases as shown in the table that follows. Take p= 1000 kg/m³ while u = 1.138 x 103kg/ms. Q2 Cases Pipe Material Water Velocity Pipe Diameter Pipe Length (m/s) (mm) (m) 1 Wrought iron 3.00 35 1000 2 Commercial steel 2.50 10 500