A 6 m vertical retaining wall is supporting a horizontal backfill of a normally consolidated soil having a unit weight of 18 kN/m3 and a friction angle of 35 degrees. Cohesion of soil is zero. (Use four decimal places) A. Determine the at rest force per unit length of the wall. B. Determine the active force develop at the wall. C. Calculate the passive force acting on the wall.

A 6 m vertical retaining wall is supporting a horizontal backfill of a normally consolidated soil having a unit weight of 18 kN/m3 and a friction angle of 35 degrees. Cohesion of soil is zero. (Use four decimal places) A. Determine the at rest force per unit length of the wall. B. Determine the active force develop at the wall. C. Calculate the passive force acting on the wall.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter12: Lateral Earth Pressure

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Similar questions

A concrete retaining wall 8 m high is supporting a horizontal backfill having a dry unit weight of 16.25kN/m3. The cohesionless soil has an angle of internal friction of 33 degrees and a void ratio 0f 0.65. (Use four decimal places) A. Compute the rankine active force on the wall. B. Compute the rankine active force on the wall if water logging occurs at a depth of 3.5 from the ground surface. C. Compute the location of the resultant active force from the bottom.
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
The channel section shown is subjected to a vertical shear force of V = 29 kN. Calculate the horizontal shear stress Ta at point A, and the vertical shear stress tR at point B. Assume a = 50 mm, b = 250 mm, tw= 16 mm, t;= 12 mm, d = 74 mm. V | tw Answers: TA = MPa TB = i MPa
A retaining wall 6 m high is supporting a horizontal backfill of soil having a void ratio of 0.5 and specific gravity of 2.7. The angle of internal friction is 32°. Compute the rankine active force on the wall if there is no water. [ Select] Compute the rankine active force on the wall if the water table is on top of the horizontal backfill level. [Select J Compute the rankine active force on the wall if the water table is at the bottom of the wall and the water content is 10%. I Select
Considering that the horizontal thrust from the back of a 5.5 m wide brick wall to the 1 m deep part of the wall is H = 55 kN a) Find the greatest stress in the base when b = 2 m.b) Find the width b so that there is a shrinkage zone at the base.(Note: unit weight of brick wall ỿ = 24 kN / m3 ) Answer: ϭmax=0,30 Mpa, b=2,23 m
Determine the lateral earth pressure force on the wall (6.0 m height shown in the figure. Draw the stress distribution and locate the location of the resultant force. Sandy soil kN Ye = 20 O = 36.0°
A retaining wall supports a horizontal backfill that is composed of two types of soil. The first layer is 4.47m high. It has a unit weight of 16.92kN/m3. The second layer is 5.76m and has a unit weight of18.51 kn/m3. If the angle of friction for both layers is 38 degrees, determine the total active force (kN) acting on the retaining wall per unit. Use stored value. Asnwer on 5 decimal places.
A retaining wall 6 m high is supporting a horizontal backfill of soil having a void ratio of 0.5 and specific gravity of 2.7. The angle of internal friction is 32°.Compute the rankine active force on the wall if there is no water.Compute the rankine active force on the wall if the water table is on top of the horizontal backfill level.Compute the rankine active force on the wall if the water table is at the bottom of the wall and the water content is 10%.
The cross section of a proposed concrete retaining wall is shown in Figure 4. The unit weight of the concrete being 24kN/m3. The soil carries a uniformly distributed load of 40kN/m2 at the top. Given c=0, f=32°, gsoil=17.5kN/m3 and µ=0.5. From the data: Check the stability of the retaining wall against sliding and overturning Determine the maximum and minimum pressure under the retaining wall.
Determine the stability of the cantilever gravity retaining wall shown in figure below. The existing soil is a clay and the backfill is a coarse-grained soil. The base of the wall will rest on a 50-mm-thick, compacted layer of the backfill. The interface friction between the base and the compacted layer of backfill is 25.0°. Groundwater level is 8 m below the base. 1.0 m Batter 1:20 0.4 m 1.8 m 9, = 20 kPa 8⁰ Ysat = 18 kN/m³ cs = 25° 8 = 15⁰ Backfill Drainage blanket Y = 23.5 kN/m³ 3 m Existing soil 6.1 m 0.9 mi Ysat = 19 kN/m³ = 35° % = 25°
You are working for a consulting firm that has been asked to evaluate the factor of safety of the wall shown in the figure supported by a well-degraded sand. The resultant load behind the concrete wall acts at the one third point. Dw 1m 1.5 m 24 kN/m³ y = 20 kN/m³ 26.5 kN/m 24° = 34° n = 0.4 3 m (a) Determine the factor of safety if Dw − D > 1.5B. Ignore the lateral passive resistance due to the soil in front of the wall. (b) Determine the factor of safety if the ground water table rises to 0.5 m below the base of the wall. Discuss the significance of your observations.
1. Given the soil profile below, determine the Total Stress and Effective Stress at points A, B, C, and D. CL 5ft y = 102 Ib/ft3 A • 9ft Ysat = 105 Ib/ft3 B 6ft SM C = 115 Ib/ft3 Ysat 12ft D