A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is applied to the assembly. A torque of 750 in-lbs is applied to the bolt and nut during assembly. The coefficient of friction between the bolt and nut is 0.200. The stiffness of the clamped material is 2x the stiffness of the bolt. The resulting stress in the bolt is:

Q: Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The…

A: According to the information we have  A screw jack's V thread has a single start with an outside…

Q: The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to…

A:

Q: (5) A 2½-in square thread steel screw is used in a common jack screw. There are 214TPI. The body of…

A: Answer: (a) The efficiency of the screw only: 27.16% (b) The efficiency of the screw & the…

Q: A certain screw jack has a pitch of 5mm and mean diameter of 180mm. The coefficient of friction…

A: Given dataPitch of the screw jack P= 5mmMean diameter Dm = 180mmCoefficient of fricition between the…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: Given: D = 110 mm θ = 40α = 160 N = 1500 rpm P = 4.4 kW μ = 0.32  A = 120 mm2

Q: The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies…

A:

Q: Q.1 Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for…

A: To find: The compression coupling for a shaft to transmit 1300 Nm. Given: The torque is T=1300 Nm.…

Q: A car engine has its rated output of 120 kW. The maxdmum - torque developed is 110 Nm, The clutch…

A: Answer: ◆ The dimensions of the friction plate are: Outer radius : ro = 133.75 mm and inner radius :…

Q: Consider the truck shown in (Figure 1). The truck has a mass of 1.45 Mg and a center of mass at G.…

A: given = mass of truck = m =1.45 Mg

Q: (a) A body of weight 55 N is placed on a rough horizontal plane. To just move the body on the…

A:

Q: A truncated conical pivot bearing which supports an axial load of 20000N from a vertical shaft…

A: Given that : Axial load, W=20000 N, Speed of shaft, N=180 rpm            ∴ ω=2πN60=2π×18060=18.84…

Q: Find the force required to move a load of 300 N up a rough plane, the force being applied parallel…

A:

Q: A con clutch must handle 200 N.m of torque at 1200 r.p.m. The maximum and minimum diameters of…

A:

Q: belt engages the smaller pulley horizontally. It is understood that the tension in the slack side of…

A: Draw the diagram of the driver and driven pulley without the jakey pulley,

Q: Q.1 Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for…

A: Answer: Given, T = 2000Nam = 2000 x 103 N - mm         τ= 50 MPa  σ t = 90MPa   No ,of bohts , N = 6…

Q: A horizontal force of F = 40 N is applied perpendicular to the handle of the lever at E. The mean…

A: The force applied is 40 N. Consider the applied torsional moment as M. Calculate M.

Q: Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: 1. A double square thread power screw has a pitch of 6 mm and mean radius of 34 mm. If it is used to…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and…

A: Frictional Force on the wheel = 0.8 X 700 = 560 N

Q: Lead screw has square threads with a pitch of 2.3 mm and a mean diameter of 16 mm. The coefficient…

A: Lead screw  Lead screw is used to translate turning motion into linear motion. Efficiency of square…

Q: pulleys are 300 and 850 mm, respectively, and the center distance is 2 m. The belt has a width of…

A: As per given question We have to determine a. The contact angles and belt length for an open…

Q: The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a…

A: Given Inner radii of hollow shaft ri=50 mm Outer radii of hollow shaft ro=100 mm Maximum allowable…

Q: b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: A clutch is a device that allows two parts with a shared axis of rotation to connect and disengage…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm  no of belt = n = 2 groove angle =  2β = 45° = β = 22.5° power…

Q: A double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a…

A:

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The…

A:

Q: An engine running at 1100 rpm drives a line shaft by means of a belt. The engine pulley has a 9 in.…

A: Belt drives are a sort of frictional drive that transmits power from one shaft to the next. a system…

Q: The nominal diameter of a triple- threaded square screw is 50 mm, while the pitch is 8 mm. It is…

A: (i) To find : The torque required to raise the load. Given : The nominal diameter of screw is d=50…

Q: A vertical power screw with double start square threads of 50 mm mean diameter and 11mm pitch is…

A:

Q: (3) A single-threaded jackscrew has square threads. The screw diameter is l in. and there are 4…

A:

Q: A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the…

A:

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight…

A:

Q: For the same question, the Impeller hub will be pressed onto the taper shaft with the Nut. How much…

A: given data; ⇒engine power(P)=27kw                        =27*103w⇒speed (n)=1684rpm⇒conical…

Q: AN ENGINE DEVELOPING 45 KW AT 1000 R.P.M IS FITTED WITH A CONE CLUTCH BUILT INSIDE THE FLYWHEEL. THE…

A: The answer is in next step

Q: The high strength, square-threaded bolt that holds the three plates together has a nominal diameter…

A:

Q: The electric motor shown in Fig. and delivers 50 in. Ib of torque to pulley A of a furnace blower by…

A: Given:Torque about pulley,TP=50 lb-inDiameter of pulley,D=5 inAngle made by V pulley,α=36οWeight of…

Q: The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a…

A: Free body diagram of the tensions on slack side and tight side To determine the minimum coefficient…

Q: Friction belt quiz Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts…

A: Given data: Write the expression of power.

Q: The block as shown in Figure 3.6 has a weight of 250 N, which is inclined at 30° to the horizontal.…

A: Below is the solution of the question mentioned

Q: The uniform bar of length L and weight is W is kept in the horizontal position by friction.…

A: Given:- Length of bar=L Weight of bar=W To find:- Smallest possible coefficient of friction, μs

Q: A horse is tied to a horizontal pole using a rope. The rope is only wrapped around the pole without…

A:

Q: 2. A pulley with a diameter of 4 in. can rotate about a fixed shaft with a diameter of 2 in. The…

A:

Q: An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a…

A:

Q: A certain screw jack has a pitch of 5mm and mean diameter of 180mm. The coefficient of friction…

A: We need to calculate the torque in raising of load

Q: The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies…

A:

Q: (1) draw free body diagram; (ii) determine the coefficient of friction; (ii) normal force; (iv)…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.