A 5.2-m-long aluminum tube (1) is to be connected toa 2.2-m-long bronze pipe (2) at B. When put in place,however, a gap of 9 mm exists between the twomembers, as shown. Aluminum tube (1) has an elasticmodulus of 69 GPa and a cross-sectional area of1980 mm2. Bronze pipe (2) has an elastic modulus of93 GPa and a cross-sectional area of 3970 mm2. Ifbolts are inserted in the flanges and tightened so thatthe gap at B is closed, determine:(a) the normal stresses ?1, ?2 produced in each of themembers.(b) the displacement (change in length of material (2),up is positive) uB of flange B with respect to supportA.5.2 m2.2 mAnswers:(a) 0₁ =(b) Ug =C(1)B(2)-95.401.1269 mmMPa, 0₂ =mm.-47.58MPa

Given : Length of aluminum tube 1 = 5.2 m Length of bronze pipe 2 = 2.2 m Elastic modulus of…

A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elasti modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If

A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elasti modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. P-108. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Figure P-108 PARTNER Aluminum A=400 mm² Steel A = 500 mm² 2.5 m 2.0 m Bronze A = 200 mm² 1.5 m 2P
904. To avoid interference, a link in a certain machine is de- signed so that its cross-sectional area is reduced one-half at section A-B, as shown in Fig. P-904. Compute the maximum tensile stress developed across section A-B if (a) the cross section of the link is 160 mm square and (b) the cross section is a circle 160 mm in diameter. Ans. (a) 75.0 MPa; (b) 85.3 MPa 80 mm P = 240 kN 80 mm $2 B Figure P-904.
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
4) 4 points Calculate the minimum net area for the plate shown below connected to 14 mm thick gusset plate with 22 mm bolts. Plate 12 mm thick 35mm 20mm 20mm 150 mm 20mm 20mm 35mm „Gusset 14 mm thick 35mm 30mm 30mm 40mm a. 936 mm? b. 918 mm? c. 900 mm? d. 887 mm?
An aluminum tube with the hexagonal cross-section shown is 2.5 ft long and has a constant wall thickness of 0.080 in. Find (a) the largest torque that the tube can carry if the shear stress is limited to 7200 psi. Use G = 4 x 106 psí for aluminum. 11.5 in 0.075 in O 6734 lb-in O 7634 lb-in O 6374 lb-in O 7346 lb-in
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Steel A-450 mm² E-200 GPa L-4.0 m A B opper A=230 mm² E-120 GPa L= 3.0 m 5.0 m a) What maximum P can be applied on the horizontal bar to give a stress of 110 MPa to steel and 150 MPa to copper. How far from copper should P be acting. Neglect the weight of the bar. b) What are the amount of deformations of the rods
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 1) What is the deformation 8Ag in mm? 10KN 0.8m 0.4m 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Policie Current Attempt in Progress A steel [E = 29900 ksi, a = 6.5x10-6/°F] bar is held between two rigid supports. The bar is stress free at a temperature of 72°F. The bar is then heated uniformly. If the yield strength of the steel is 45 ksi, determine the temperature at which yield first occurs. Answer: T= i °F