A 400V three-phase, four wire dystem has the following loads connected: Phase 1: Load impedance Z1= 4- + j15 Ohms Phase 2: Load impedance Z2 = 60 Ohms Phase 3: Load impedance Z3 = 15 - j20 Ohms Draw the circuit diagram and determine: The line and phase voltages for all phases (Including phase angles)

A 400V three-phase, four wire dystem has the following loads connected: Phase 1: Load impedance Z1= 4- + j15 Ohms Phase 2: Load impedance Z2 = 60 Ohms Phase 3: Load impedance Z3 = 15 - j20 Ohms Draw the circuit diagram and determine: The line and phase voltages for all phases (Including phase angles)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Similar questions

Draw three transformers for each of the different three-phase connections. That is, draw three transformers and then make the connection, eg star-star, then redraw three transformers and make another three-phase connection, and so on until all four combinations of three-phase connections are made.
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
7. Three load units A, B, and Care connected in parallel and take currents that are respectively 11 A, 10A and 15A. Assuming IA to be the reference phasor, IB leads IA by 30degrees and IC legs behind IA by 65degrees. Calculate the total (resultant) currentand angle it makes with the x-axis.
Positive sequence components consist of 3 equal sized phasors. The phase difference between these phasors is 180 °. And the phasors are in the phase order of the true phasors. Is this statement true or false?
Discuss how delta connection is achieved in three-phase systems?
A balanced Y-connected voltage source with Eag=2770volts is applied to a balanced-Y load in parallel with a balanced- load where ZY=20+j10andZ=30j15ohms. The Y load is solidly grounded. Using base values of Sbase1,=10kVAandVbaseLN=277volts, calculate the source current Ia in per-unit and in amperes
A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).
what are the advantages and Disadvantages Connecting transformers 3 Phase between (delta to Star)
3. Single-phase T1-transformer with a power of 500 kVA and a single-phase T2- with a power of 400 kVAtransformers are connected in parallel and load 1000 kVA with 0.8-back power factor.they are feeding. The equivalent circuit winding resistance of T1 is 0.025 b and the equivalent circuit reactance is 0.06is b. The equivalent winding resistance of T2 is 0.016 b and the equivalent circuit reactance is 0.07 b. Bothhas the same conversion ratio in the transformer.a. Draw the connection diagram given in the question. b. Obtain the power sharing expression over the parameters given in the question. c. Calculate the kVA values and power factors of the transformers.
4. Three-phase circuit