A 381 V, 50 Hz, Y-connected, eight poles synchronous generator has the OCC given in tabular form below (Phase Voltage versus the field current). The generator has a per-phase synchronous reactance of 0.2 Q, and a negligible armature resistance. At full-load: The machine supplies 690 A armature current at 0.8 PF lagging. How much field current must be supplied to the generator to make the terminal voltage 380 V? E. (V) IF. (A) 0 65 125 260 290 320 350 380 420 450 470 0.00 0.5 10 2.0 2.25 2.55 27 3.0 3.7 4.1 4.25 Answer: The required field current is: Amperes.

A 381 V, 50 Hz, Y-connected, eight poles synchronous generator has the OCC given in tabular form below (Phase Voltage versus the field current). The generator has a per-phase synchronous reactance of 0.2 Q, and a negligible armature resistance. At full-load: The machine supplies 690 A armature current at 0.8 PF lagging. How much field current must be supplied to the generator to make the terminal voltage 380 V? E. (V) IF. (A) 0 65 125 260 290 320 350 380 420 450 470 0.00 0.5 10 2.0 2.25 2.55 27 3.0 3.7 4.1 4.25 Answer: The required field current is: Amperes.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
A compound generator has a lap-wound armature with 200 slots and four turns per coil. It is rotating with a speed of 80 rpm and flux per pole is 100mWb. The armature resistance is 12 and shunt field resistance is 2002. The series field resistance is 22. Determine: (i) Terminal voltage (ii) If a load is connected to the terminals which starts pulling a load current such that the flux that is produced by the series field is added into the shunt field to keep the new induced voltage to be the same as the induced voltage at no load, what will be the new terminal voltage if the shunt field current is dropped to 90% of the shunt field current at no load? (iii) Power dissipated in the load Draw equivalent circuits
True False In self-excited DC generator, the residual flux is primary condition in e.m.f generation Answer by true or false * True False The flux of shunt wound DC generator induced during loading
A 4 pole dc shunt generator with a shunt field resistance of 100 ohm and an armature resistance of 1 ohm has 378 wave connected conductor in its armature. the flux per pole is 0.02wb, if the load resistance of 10 ohm is connexted across the aemature terminal and the generator driven at 1000rpm, calculate the power obsorbed by load
The armature reaction occurs when a separately excited generator supplies rated load: Is always present Is always absent May be sometimes present None of the above
A short shunt compound generator supplies 100A at 110V. Armature resistance is 0.050 and the shunt field resistance is 570 and the series field of resistance is 0.042. if the SPL is 852, determine a)Eg b)Copper lossesin b.1)armature b.2)series b.3)shunt c)n
A synchronous generator is connected to a pure capacitive load. The field excitation is kept constant and the stator resistance is assumed negligible. Explain, with the help of phasor diagram(s), how the generator’s terminal voltage will vary when the capacitive load is increased while the power factor is kept constant.
.Two dc shunt generators A and B are rated at 100 and 150 kW at 110 V respectively, Their external load characteristics may be considered as straight line. The voltage drop In the terminal voltage from no-load to full-load is 10 v for A and 20 V for B. Determine the operating voltage when these generators are operated in parallel to supply a load of 220 kW.
A 4 pole generator with wave wound armature has 54 slots each having 20 conductors. The flux per pole is 0.01 Wb. ) At what speed must the armature rotate to give an induced EMF of 225V is, (11) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is, search
A 500 V, 250 kW, long shunt compound generator induces an e.m.f. of 480 V whenrunning at 1000 r.p.m. no load. On full load the spped of the machine drops to 975r.p.m. the flux increases by 15% and the terminal voltage rises to 500 V. If theseries and shunt field resistances are 0.02 ohm and 100 ohms respectively,calculate the armature resistance. Assume a voltage drop of 1V per brush.[Ans.
4 The field current of a synchronous generator is adjusted to give an air-gap flux of 0.01 weber per pole. The flux is sinusoidally distributed along the air gap. The armature winding is Y-connected. There are 5 slots/phase/pole and the coil pitch is 12/15. The frequency is 60 hertz at 1,200 RPM. (a) Calculate the emf/turn. (b) If there are 10 turns/ coil and two coil sides per slot, calculate the emf per phase. (c) Calculate the emfbetween terminals. Ans. 2.53V; 728V; 1,260V.
A shunt DC generator has no load terminal voltage of 140V. Armature resistance is 1ohm and shunt field resistance is 50ohm. Calculate the induced voltage.