A 250 V dc shunt motor has an armature resistance of 0.2 Ω and a field resistance of 100 Ω. When the motor is operated on no-load at rated voltage. It draws an armature current of 5 A and runs at 1200 rpm. When a load is coupled to the motor, it draws total line current of 50 A at rated voltage, with a 5 % reduction in the air-gap flux due to armature reaction. Voltage drop across the brushes can be taken as 1 V per brush under all operating conditions. The speed of the motor, in rpm, under this loaded condition, is closest to

A 250 V dc shunt motor has an armature resistance of 0.2 Ω and a field resistance of 100 Ω. When the motor is operated on no-load at rated voltage. It draws an armature current of 5 A and runs at 1200 rpm. When a load is coupled to the motor, it draws total line current of 50 A at rated voltage, with a 5 % reduction in the air-gap flux due to armature reaction. Voltage drop across the brushes can be taken as 1 V per brush under all operating conditions. The speed of the motor, in rpm, under this loaded condition, is closest to

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

250 v ,4pole wavw wound DC series motor has 782 conductors on its armature and series field resistant of 0.75 ohm the motor takes a current of 40amp esstimate its speed and its torque developed if it has a flux per pole of 2mWb
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
• Q5/ in a DC motor. List and describe the types of losses that occur
A 230v DC series motor takes 30A when giving its rated output at 1400 rpm. It has a field resistance of 0,4 ohms, Calculate the value of the resistance (Ra) of the armature when Eb = 200V. Select the correct response: 0.2 ohms 0.6 ohms 0.8 ohms 0.4 ohms
A DC shunt generator delivers 45 A at a terminal voltage of 220 V. The armature and the shunt field resistances are 0.01 2 and 44N respectively. The stray losses are 375 W. What is percentage efficiency of the DC generator
The DC shunt generator with the terminal voltage 350 V, armature drop 7 V and the each brush drop 2 V, then the value of generated emf is
The current drawn by 220 V dc shunt motor of armature resistance 0.5 ohm and back emf 200 V is
Q9 / What are the function of brushes , pole and commutator in DC machine
A direct current shunt dynamo continuously supplies an ohmic load of 50 Ohm at terminal voltage Vt= 1000 V. The armature winding resistance is 5 Ohm and the shunt pole winding resistance is 200 Ohm. The sum of mechanical losses is 400 W. What is the percent efficiency of the dynamo under these operating conditions? a) 70 b) 74 c) 87 d) 78 e) 85
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
6. The motion in DC motor can be increased by the following factors... (you may choose more than one) * a) Using a stronger magnet b) Increasing the potential difference c) Increasing the current d) Increasing the number of turns on the coil
Q- The armature resistance of a permanent magnet dc motor is 0.80. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be