A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.

A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9P

See similar textbooks

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
Answer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohm
Q6 Complete the answer : If connected .................... to the transformer changes, copper loss varies.
10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and the number of turns of the low voltage winding is N2=34. The high voltage winding is energized with V1= 10 kV rms line-to-line and V2= 400 V rms line-to-line has been taken from the low voltage winding. What is the connection of the low voltage winding if the high voltage winding is Y-connected? Εισαγάγετε την απάντησή σας
1. Explain why transformer saturation occurs at a lower voltage value when the frequency of the ac power source is decreased? 2. What are the effects of decreasing the frequency of the ac power source on the waveform and the rms value of the magnetizing current of a power transformer? 3. What are the effects of increasing the frequency of the ac power source on the waveform and the rms value of the magnetizing current of a power transformer?
1. Explain why transformer saturation occurs at a lower voltage value when the frequency of the ac power source is decreased?
Can we use dc supply on transformer ?
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
Q7/ Complete the blank The copper loss of a transformer at 4/5 of the full load is 4000 W, full load copper loss will be..........................................?
1.a. For performing dielectric-strength tests on insulating materials, two transformers are connected in aA. parallel combination.B. cascade arrangement.C. polyphase arrangement. 1.b. In large power transformers, the unequal voltage distribution caused by voltage surges in the winding isprevented by the use ofA. static shields.B. series capacitors.c. low-voltage arresters.