A 100/S00 V. 1 KVA, 50 Hz transformer was put through open and short-circuit tests to find its internal parameters. The test conditions and derived parameters are as follows Open circut test: The high voltage side terminals were open. The low voltäge side was connected to 10020ª, 50 Hz supply. The low voltage side current was measured as 50245º MA. Short-circuit test The high voltage side terminals were short-circuited. The low voltage side was connected to a variable voltage supply (50 Hz). A full load current of 102-30° A was achieved when the variable voltage supply was at 820° V. The transformer was then put to operation by connecting a load of 400230° 2 to the high voltage side (secondary) while applying a primary voltage of 10020° V. Calculate the primary current (the current drawn from the power supply).

A 100/S00 V. 1 KVA, 50 Hz transformer was put through open and short-circuit tests to find its internal parameters. The test conditions and derived parameters are as follows Open circut test: The high voltage side terminals were open. The low voltäge side was connected to 10020ª, 50 Hz supply. The low voltage side current was measured as 50245º MA. Short-circuit test The high voltage side terminals were short-circuited. The low voltage side was connected to a variable voltage supply (50 Hz). A full load current of 102-30° A was achieved when the variable voltage supply was at 820° V. The transformer was then put to operation by connecting a load of 400230° 2 to the high voltage side (secondary) while applying a primary voltage of 10020° V. Calculate the primary current (the current drawn from the power supply).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.10P: A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding...

See similar textbooks

Similar questions

For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
Question:4 A Step-down transformer is given and calculate 5:1 120 V 60 Hz V2 i k2 i. Peak load and D.C. load voltage ii. D.C. Current
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. Find the average power spent by the load circuit?
How do i calculate secondary current in transformer analysis
In this Center tapped transformer Find the peak voltage of V1 and V2, RMS voltage of V1 and V2, and Peak to peak voltage of V1 and V2
The voltage per winding of the 220V/12V, 50 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, the cross-sectional area of the core in cm 2 is equal to which of the following. O 0.0050 30 50 O 0.0025 0.0030 O 60 0.0060 O 25
The losses found in a transformer