Q1. Choose only seven for the following:1) ..........................of measurement is difference between measured values and true values.expressed in units of the measured quantity.a. percent error2)b.relative errorc.absolute error**********.........closeness with which an instrument reading approaches the true value of thevariable being measured.a. resolutionb.sensitivity3)c.accuracy**********a. Working Standardsare the basic reference standards used in industrial measurement laboratoriesThe resolution for instrument is .......... When the readings of the instrument in volts wereb.Secondary Standards e.International StandardsXI-1.1, X2-1.2, X3-5, X4-5.2a.IVb.0.1Vc.0.2V5) The percent error..............when the voltmeter measures the voltage-1.41 V. and the truevalue of voltage=1.44 V.a. 0.208%.b. 20.8%.c. 2.08%6)*******are divided into two categories, instrumental error and environmental error.a. Systematic errorsb. Gross errorsc.Random errors7) The magnitude of the limiting error...............when A 600 V volimeter is specified to beaccurate within + 3% at full scale. Also the instrument is used to measure a voltage of 156 V.c.18Va. 6Vb.12V8)....................is the magnetic force that causes the pointer to move from its zere position when xcurrent flows. This force is established due to the interaction between thea. Deflection force.b.Controlling force.***... of units.c.Damping force.9) The International System of Units establishes......a. two kinds b. three kinds e. four kinds

Given Multiple choice questions based on measurement. Please find the below attachment for clear…

91. Choose only seven for the following: 1) ******** ............of measurement is difference between measured values and true values. expressed in units of the measured quantity. a. percent error b.relative error 2) ******** .........closeness with which an instrument reading approaches the true value of the variable being measured. cabsolute error a. resolution b.sensitivity c.accuracy 3) a. Working Standards ...are the basic reference standards used in industrial measurement laboratories 4) The resolution for instrument is .......... When the readings of the instrument in volts were b.Secondary Standards c.International Standards XI-1.1, X2-1.2, X3-5, X4-5.2 a.IV b.0.1V Cozy 5) The

91. Choose only seven for the following: 1) ............of measurement is difference between measured values and true values. expressed in units of the measured quantity. a. percent error b.relative error 2) .........closeness with which an instrument reading approaches the true value of the variable being measured. cabsolute error a. resolution b.sensitivity c.accuracy 3) a. Working Standards ...are the basic reference standards used in industrial measurement laboratories 4) The resolution for instrument is .......... When the readings of the instrument in volts were b.Secondary Standards c.International Standards XI-1.1, X2-1.2, X3-5, X4-5.2 a.IV b.0.1V Cozy 5) The

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q) In measurement system, which of the following static characteristics are * ?desirable Ll 5 Accuracy. All of above. Sensitivity. Resolution.
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
This question would help revise concepts related to MOS device and basic circuit design. Please mark all correct answers to the following multiple choice questions. 1.1. Which of the following are true about MOSFET devices? (a) MOS stands for "Metallurgy Of Semiconductors" (b) MOSFET current conduction is due to drift phenomenon (c) An externally induced voltage at the gate is fundamental to inversion layer (d) Naming of "Source" and "Drain" regions are only dependent on aspect ratio 1.2. Which of the following are true about NMOS transistors (a) The threshold voltage can be positive or negative depending on geometry (b) Channel length modulation parameter (A) is always positive (c) Current flows from drain to source (d) Threshold voltage is a fixed value based on process, it cannot be changed by external voltages 1.3. In a MOS device (a) Cas and CGp both have both geometry and voltage dependencies (b) Cas is takes minimum value at saturation while CGD goes to maximum value (c) CoB and…
Q) In measurement system, which of the following static characteristics are ?desirable Resolution. O All of above. O Accuracy. O Sensitivity.
Which statement is true? a. In FSK, the modulating signal and the carrier signal are both analog b. In FSK, the modulating signal and the modulated signala re both digital c. In FSK, the modulating signal and the modulated signal are both analog d. In FSK, the carrier signal is analog and the modulating signal is digital
1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a multisim program..................... must be entered. 2)) the frequency of the signal generator to produce a signal with a period of 10ms...................... must be entered as. What should come to the dotted line?
Percent (%) Total Harmonic Distortion of Signal Equal to which of the following.
1) what is the Voltage & Current rating ofTriode for Alternating Current (TRIAC) 2) 5. Are the following statements correct or wrong? Justify your answer.(a) Thyristors are used only for low voltage, low current applications.(b) MOSFETs are used for high frequency applications.(c) BJT is more efficient than IGBT in high power applications.(d) GTO requires very low current applied to its gate to be turn off.(e) IGBT is a voltage driven device.
For an efficient communication in PCM system, the number of samples per second must be at most be equal to twice the highest modulating frequency.a. A very important considerationb. No, it must be at least equal to twice the highest modulating frequencyc. 80-50 percent true
Solve the 2nd question i.e. the value of the output signal is equal to.......
(004) (1)- Problem - Common Emitter Fixed Bias Amplifier. (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?