9. Angle bars are used for the determinate truss as shown in the figure. Horizontal and vertical members are L6x4x1/2. Diagonal members are L5x3x1/4. Determine the ADEQUACY OF MEMBERS AB AND BC based on factored loads shown. Bolt diameters=22 mm. Use A-36 Steel. 423 kN Зт 3m 3m Connection Details 50mm B. D. 3m 62mm 5m F 300mm

9. Angle bars are used for the determinate truss as shown in the figure. Horizontal and vertical members are L6x4x1/2. Diagonal members are L5x3x1/4. Determine the ADEQUACY OF MEMBERS AB AND BC based on factored loads shown. Bolt diameters=22 mm. Use A-36 Steel. 423 kN Зт 3m 3m Connection Details 50mm B. D. 3m 62mm 5m F 300mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Bottom chord of truss is composed of two angle bars each having a dimension of 185 mm x 146 mm x 8.7 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 44 mm and 59mm pitch. Use A36 steel Fy 248 MPa Fu = 400 MPa %3D spacing of bolt = 68.9 mm %3D 9 5mm thick gunset plate edge dist Compute the capacity of the bottom chord based on block shear strength, in KN. uad
Bottom chord of truss is composed of two angle bars each having a dimension of 192 mm x 95 mm x 5.4 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 40 mm and 63.5mm pitch. Use A36 steel Fy = 248 MPa Fu = 400 MPa spacing of bolt = 59.4 mm Compute the capacity of the bottom chord based on block shear strength, in KN. 9.5mm thick gusset plate edge dist
PLATE NO 3 Method of Sections Chapter 5 Problem 5-2 Page 76 Using the method of sections, determine the kind and amount of stress in the following members of the truss shown in figure P5-2 (page 76). U:U2 UıL2 LIL2 U2U3 U2L3 L2L3 1000lb 1000lb U3 1000lb 1000lb 1000lb U2 U4 500lb Ui 500lb h=20ft Us Lo L1 L2 L3 L4 Ls RAV 6 panels at 10' = 60 ft RBv
The figure shows a truss and the detail of the riveted connection at joint H. Using allowable stresses ofτ = H MPa and σb= I MPa, how many 19-mm diameter rivets are required to fasten member HB to thegusset plate? Member HC? Round-up your answer to a whole number F=162 H=110 I= 180
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the design tensile strength for LRFD. Select one: а. 78 b. 66 С. 132 d. 156
Select an economic WT shape section for the tension member BH and GC for the truss shown. Note: Verify your answer by solving ØPn Assumptions: Use A36 steel. Assume there are two or three bolts in the direction of loading There are two bolts in the transverse direction and not staggered arranged. Use a 7/8-inch diameter bolt. Given: P = P,, = 1.2DL + 1.6LL DL = 30 kips LL = 65 Kips Н F 15 ft 30 ft A E B D 40 ft- 40 ft- 40 ft - 40 ft- 1.5P P
SOLVE FOR THE FORCE IN MEMBERS AB, AC, BC, CD, BD, BE, DE, DF & EF. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL ALSO SEE LINK UNDER WEEK7 0.8m 2.4m -6KN MEMBER AB AC BC CD BD BE 2m ED DF EF 1m 8KN Av REACTION hinge) EX REACTION @roller) 3m SUMMARY OF RESULTS FORCE 1m 10KN 2.4m 3KN NATURE(I or C)
Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf-120mm d=550mm d'=80mm fc'=34MPa fy=415MPa USE NSCP 2015 A.Mu = 1300kN-m, As = mm2 B.Mu = 1800kN-m, As = mm2, As' = mm2
... A36 (Fy=36ksi; Fu=58ksi) steel is used for the tension member shown. a. Determine the design strength based on the gross area. b. Determine the design strength based on the net area. - PL % ×12 2" 5/8" 2" 4" 12" 4" 2" 4-in.-diameter bolts Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
7.2 A5/g x 15 DF axial combination 5 glulam is used as the tension member in a large roof truss. A single row of 1-in. diameter bolts occurs at the net section of the member. Loads are a combination of dead and snow (ASD: D + S; LRFD: 1.2D + 1.6S). Joints are assumed to be pin-connected. MC = 10 percent. C; = 1.0. Find: a. The maximum axial tension load using ASD. b. Repeat part a except that the MC = 15 percent. c. Repeat part a except that the MC = 18 percent. d. Repeat part a except that the member is a bending combination 24 F-V8 DF glulam. e. The factored axial tension capacity using LRFD. f. Repeat part e except that the MC = 15 percent. g. Repeat part e except that the MC = 18 percent. h. Repeat part e except that the member is a bending combination 24F-V8 DF glulam.
Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. 30 degrees Assume U= 0.85. All steel will be A36. PL늘X1 C10 C10 11 in PL x 11 11 in