8-32 Water at 15°C (p = 999.1 kg/m³ and u = 1.138 × 10-3 kg/m-s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. 10 L/s - 30 m- FIGURE P8-32 6 cm

8-32 Water at 15°C (p = 999.1 kg/m³ and u = 1.138 × 10-3 kg/m-s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. 10 L/s - 30 m- FIGURE P8-32 6 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Water is following steadily through a 50 m long section of a horizontal 5-cm diameter stainless steel pipe. The water temperature is 15°C and the flow rate is 9 L/s. Determine: a.) The pressure drop over the pipe length [kPa]. b.) The head loss [m]. c.) The pumping power needed to overcome the pressure drop (assume a pump efficiency of 67%) [kW]. 9 L/s 5 cm 50 m
Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm-100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?). 5 m
Consider the water distribution network. Given the information below, find the flow rate between A and В. A pipe has an absolute roughness of 0.0008 ft. 1.5 MGD of 50 deg F water (kinematic viscosity is 1.410 x 10-5 ft2/s) enters at junction A and leaves at junction B. The acceptable pressure at point D is 40 psig (280 kPa). Elev. 570 ft A 2000 ft. 10in B Elev. 580 ft 1000 ft. 12in 1100 ft. 10in Elev. 590 ft 1500 ft. 8in Elev. 610 ft
Q3/ The water levels in the two reservoirs A and B are 104.5 m and 100 m respectively above the datum. Pipe joins each to a common point D, where pressure is 98:1 kN/m”*2 gauge at above the joint point D and height is 83-5 m above datum. Another pipe connects D to another tank C. What will be the height of water level in C assuming the same value of ‘f’ for all pipes. Take friction co-efficient f = 0-0075. The diameters of the pipes AD, BD and CD are 300 mm, 450 mm, 600 mm respectively and their lengths are 240 m, 270 m, 300 m respectively. 100 m Your answer
Determine the discharge in the pipe and the pressure at point B. The total head loss from tank water surface to point B is 0.5 m; the total head loss from point B to the outlet is 1.5 m. The water temperature is 10°C. Assume turbulent flow at all locations. What is the pressure at point B? Water O 5.75 kPa 7.97 kPa O 4.64 kPa O 6.86 kPa 1.5 m 3.5 m B 40 cm diameter -20 cm diameter nozzle
Problem 7 -75 A tube 15 m long is to connect two large tanks whose difference in water level is 2 m. The fube is to carry 5L/s of flow. What minimum size of tube is necessary to assure laminar flow condition? Ans: 55 mm
7. Barometeric pressure is 101.3 kPa and vapor pressure of water is 32.4 kPa. Calculate the elevation (in meters) of the tubing end 3 for maximum flowrate through this pipeline. Also sketch the energy line, EL (color red) and the hydraulic grade line, HGL (color blue) on the drawing for this situation. El. 34 Water 150 mm d EI. 30.5
Water is flowing in the straight 100mm diameter coated cast iron as shown in the figure. Due to continous supply, the water level of the reservoir remains constant at all time. By using Darcy Weisbach and Hazen William's formula of head loss, determine the flow rate in the pipe. (Ans.: DW:1786.2 liters/min, HW: 2144.4 liter/min) EL85M 180 m opened end EL50M
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KP.. Determine the discharge at the pipe. A No answer among the choices B) Q = 132.74 L/s c) Q = 172.81 L/s D) Q = 118.43 L/s E) Q = 153.68 L/s F) Q = 101.07 L/s
Observation wells A and B are located in the direction of flow, Water level in well A is Ha and in well B is Hb. Point C is between AB and on the AB line. What is the height (m) of water level at point C? (There is no pumping here. Wells are for observation only) Ha, m 66 Hb, m cm/s 50 Hydraulic conductivity, K 0.02 AC, km 1.3 Determine the Darcy velocity (cm/s) for water flowing through a sand column with the following characteristics: Hydraulic head drop cm BC, km 6 0.5 The sand column length cm 55
Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine the the required pumping power input for flow over a 200-feet long section of the pipe. A 530 Watts В 461 Watts C) 315 Watts D) None of the above
a. Determine the velocity of flow in the pipe in m/s. b. Determine the discharge Q in m^3/s. c. How many meters above the center of the pipe will water stand in piezometer tube 3? d.