700 KN 2.5m A 2.5-m length of a steel pipe of 300-mm outer diameter and 15-mm wall thickness is used as a column to carry a 700-kN centric axial load. Knowing that E=200 GPa and v=0.30, determine (a) the change in length of the pipe, (b) the change in its outer diameter, (c) the change in its wall thickness.

700 KN 2.5m A 2.5-m length of a steel pipe of 300-mm outer diameter and 15-mm wall thickness is used as a column to carry a 700-kN centric axial load. Knowing that E=200 GPa and v=0.30, determine (a) the change in length of the pipe, (b) the change in its outer diameter, (c) the change in its wall thickness.

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter11: Fluid Statics

Section: Chapter Questions

Problem 27PE: A certain hydraulic system is designed to exert a force 100 times as large as the one put into it....

See similar textbooks

Similar questions

A certain hydraulic system is designed to exert a force 100 times as large as the one put into it. (a) What must be the ratio of the area of the slave cylinder to the area of the master cylinder? (b) What must be the ratio of their diameters? (c) By what factor is the distance through which the output force moves reduced relative to the distance through which the input force moves? Assume no losses to friction.
Verigy that the SI of hpg is N/m2.
600 lb ! A 600-lb tensile load is applied to a test coupon made from 1-in. flat steel plate (E = 29 X 10° psi, p = 0.30). Determine the result- ing change (a) in the 2-in. gage length, (b) in the width of portion AB of the test coupon, (c) in the thickness of portion AB, (d) in the cross-sectional area of portion AB. 2 in. -600 lb A B F
A flanged bolt coupling consists of ten steel 1/2-in.-diameter bolts spaced evenly around a bolt circle 14 in. in diameter. Determine the torque capacity of the coupling if the allowable shearing in the bolts is 6000 psi.
The cylindrical tank with a spherical end-cap has an outer radius of 2 m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal and circumferential stresses in the cylinder, and the stress in the end- cap. 45° 2 m
The propane gas tank has an inner diameter of 2500 mm and wall thickness of 18 mm. If the tank is pressurized to 5 MPa, determine the absolute maximum shear stress in the wall of the tank
9-90. The starter for an electric motor is a full cylinder and has the cross-sectional areas shown. If copper wiring has a density of Peu = 8.90 Mg/m³ and the steel frame has a density of Pst = 7.80 Mg/m³, estimate the total mass of the starter. Neglect the size of the copper wire. Problem 9-90 Steel Copper 80 mm 50 mm 30 mm 100 mm 60 mm
By how much will a 220 cm length of copper ( Y for Cu = 117,000 MPa) wire, 2.2 mm in diameter, elongate when a 4.8 kg mass is hung from its end?
For lack of a suitable material supply, a thin-walled cylinder is machined from a thick plate of 7178-T651 aluminum alloy such that the cylinder axis is oriented parallel to the rolling direction of the plate. If the cylinder’s diameter and wall thickness are 5 cm and 0.5 cm, respectively, determine whether the cylinder could withstand a pressure of 50 MPa in the presence of a 0.2-cm-deep semicircular surface flaw.
The flow through a ½ in diameter pipe is 4 GPM with a pressure drop of 1 PSI. What would the pressure drop be for the same flow through a 1.5 in diameter pipe?
A vertical plate is isolated from its support by two rubber blocks which each have dimensions a = 0.020m, b = 0.050m and c = 0.080m. If the maximum load is 200 N determine the maximum plate vertical deflection (G = 350 kPa for the rubber).
A spruce tree is 20 m tall with a trunk diameter of 0.4 m. Its needles have a measured water potential of –2.5 MPa, while the roots have a measured water potential of –1.2 MPa. Hydraulic conductivity through the stems is 7×10–8m3s/kg. What is the transpiration rate of the tree (in g H2O/s), assuming that 1.5% of the stem cross sectional area contains water-conducting vessels? Hints: 1 MPa = 106kg/(m·s2); water density = 1 g/cm3 Start by using the flow equation (p. 104 CMV textbook) to calculate the rate of water movement in m s-1 Multiply the rate by the cross-sectional area of water-conducting vessels