6. A steel wire 2m long and 3 mm in diameter is extended by 0.75 mm when a weight P is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 long and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that of steel be 2.0 x 10^2 N/mm^2. a. 0.976 x 10^5 N/mm^2 c. 0.293 x 10^5 N/mm^2 b. 0.183 x 10^5 N/mm^2 d. 0.909 x 10^5 N/mm^2

6. A steel wire 2m long and 3 mm in diameter is extended by 0.75 mm when a weight P is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 long and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that of steel be 2.0 x 10^2 N/mm^2. a. 0.976 x 10^5 N/mm^2 c. 0.293 x 10^5 N/mm^2 b. 0.183 x 10^5 N/mm^2 d. 0.909 x 10^5 N/mm^2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A steel wire 2 m long and 3 mm in diameter is extended by 0.75 mm when a weight W is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 m long and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that of steel be 2.0 x 10° Nhmm².
Determine the following for the bar. A) B) C) D) σ, ksi 100 ksi 80 ksi T, ksi 40 ksi What is the Modulus of Elasticity for the material of the bar. What tensile force will cause the bar to yield? What will be the length of the bar after a 540 kip force is applied? What will be the cross sectional dimensions after a 300 kip force is applied? 0.0025 0.0035 0.0095 0.0100 0.0130 0.0145 Y, radians ɛ, in/in 20 in 3 in Cross Section 2 in
8. A rigid bar AB is supported by three rods. A load P = 350 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2. Steel rod A = 900 sq. mm Steel rod A = 900 sq. mm 2 m Copper A = 1200 sq. mm 2 m %3D A B 1 m -1m Determine the deformation in the rods (in mm). * Your answer
4. A steel wire 2 m long and 3 mm in diameter is extended by 0.75 mm when a weight W is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 m long and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that of steel be 2.0 x 10° Nhmn.
8. A rigid bar AB is supported by three rods. A load P = 350 kN is applied to the bar. The %3D modulus of elasticity of copper is 110 x 10^6 kN/m^2 and modulus of elasticity of steel is 200 x 10^6 kN/m^2. Steel rod A = 900 sq. mm Steel rod A = 900 sq. mm 2 m |Copper A = 1200 sq. mm 2 m A B 1 m - 1 m Determine the deformation in the rods (in mm). * Your answer Вack Next Clear form Never submit passwords through Google Forms. This form was created inside of Saint Louis University, Inc..
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (sce figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile load P = 22 kN? (b) If the same volume of material is made into a bar of constant diameter d and length 2.4 m, what will be the clongation under the same load P? (c) If the uniform axial centroidal load q = 18.33 kN/m is applied to the left over segment 1 (sce figure part b), find the ratio of the total elongation of the bar to that in parts (a) and (b). Įd1 = 20 mm Įd2 = 12 mm %3D P= 22 kN 1.2 m- -1.2 m (a) q = 18.33 kN/m [d1 = 20 mm |d2 = 12 mm P = 22 kN 1.2 m (b)
Bronze Steel Steel W = 40 kips %3D 2 ft 2 ft 2.
Q5 A specimen of magnesium having a rectangular cross section of dimensions (3.2 mm X 19.1 mm) and gage length 63.5 mm is deformed in tension. Using the load-elongation data tabulated as follows load (N) and Extension (mm), Find the standard mechanical properties. load 1380 2780 5630 7430 8140 9870 12850 | 14100 14340 13830 12500 Ext. 0.03 0.06 0.12 0.2 0.25 0.64 1.91 3.18 4.45 5.72 6.99 a) Draw the stress strain curve. b) Find the young modulus. c) Find the proof stress d) Find the ultimate tensile strength. e) Find the fracture stress f) Find the maximum strain.
The cross-sectional area of the bar is 5 cm. Use E = 70 GPa for aluminum, and g= 200 GPa for steel. L. Aluminum Steel Aluminum 80 kN 20 kN -30 kN +70 kN A IB +3 m 4m 5 m What is the elongation in segment AB (Aluminum)? * O -6.8571 x10^-3 m O 6.8571 x10^-3 m O -7.8571 x10^-3 m O 7.8571 x10^-3 m What is the elongation in segment BC (Steel)? * O 2 x10^-3 m O 3x10^-3 m O -3x10-3 m O -2 x10^-3 m What is the elongation in segment CD (Aluminum)? * O 6.8571 x10^-3 m O -2.8571 x10^-3 m O 2.8571 x10^-3 m O -6.8571 x10^-3 m What is the total elongation of the bar? * 6 x10^-3 m O 5 x10^-3 m O 4 x10^-3 m O -6 x10^-3 m
9. If d be the diameter of MS or tor steel bars in mm, the standard weight (in kg) per metre of the bar is 100 (a) 0.00618 d² (b) 0.00618 d (c) 0.00816 d² (d) 0.00816 d
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.8 in?, 1.07 in?, and 0.56 in? respectively.Determine the change in length (in inches) of the bar if P = 11280 Ib.The moduli of elasticity are 30092 ksi for steel,12006 ksifor bronze, and 10002 ksi for aluminum. Round off the final answer to four decimal places. Bronze Steel Aluminum 2 ft 4 ft 3 ft P 2P 3P 4P
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 415 mm?, 636 mm² , and 253 mm² respectively.Determine the change in length (in mm) of the bar if P = 28084 N.The moduli of elasticity are 83.77 GPa for bronze ,71.95 GPafor aluminum , and 204.98 GPa for steel. Round off the final answer to four decimal places. Bronze Aluminum Steel 2P ЗР P. 4P 0.6 m →k 1.0 m 0.8 m Add your answer