5. Use superposition to calculate the current i, in Circuit 5.

Q: Question 01: Derive the circuit of an 8-to-3 priority encoder.

A:

Q: Control Systems > Controllers and Compensators Question A phase lead compensating network ha its…

A: Given- A phase lead compensating network, Transfer function- Gcs=101+0.04s1+0.01s, To Find- The…

Q: For a Rf = 1003 If IA Find separately excited DC generator Rf m Off - Ia Ef Pin Pout % eff T Fa +…

A:

Q: Design a V/F converter as shown in Fig. 16.64 so that fo = 2.5 kHz at v₁ = 5 V. The input voltage v₁…

A: Given f0 =2.5 kHz v1 =5 V v1 is variable between 10 mV and 10 V

Q: 4. A 6 W night light is plugged into a 110 V circuit and operates continuously for 1 year. Find the…

A: In this question We need to determine the current, resistance and energy in the circuit.  We know…

Q: Question #7) Given the following transmission line that is terminated with an ideal "short circuit":…

A: Given, The diagram of the transmission line,

Q: 1. Boolean equation f(x,y,z)=x'z +x'y + xy'z+yz A. Simplify the equation algebraically. B. Simplify…

A:

Q: 7. During 100 percent modulation, what percentage of the average output power is in the sidebands?…

A: We need to find out the percentage power of side band and carrier.

Q: Find poles and zeros of the system having the following transfer function G(s) then show the poles…

A: We need to find out the pole and zero for given system and we need to check stability of given…

Q: (o) is 15 kHz and f: = 3 kHz. Repeat for f: = 2.5 and 5 kHz.

A: The bandwidth of FM signal has been calculated using Carson's rule.

Q: A 30, 460 V, 60 Hz, 20 kW induction machine draws 25 A at a power factor of 0.9 lagging when…

A:

Q: What is the different between Open Loop and Close Loop system? Give an example

A: Closed Loop system: When system's control action determines how the output will turn out that kind…

Q: 6. Find the Thevenin equivalent circuit at terminals a and b. 5230" A 2092 -j1592 T elleb O a 12502…

A: Given: Circuit diagram:

Q: Problem # 11.1 Assuming no transients are present, calculate the instantaneous power absorbed by…

A: We need to determine the average power absorbed by each element & power supplied by source…

Q: Determine the carrier swing of an FM broadcast transmitter a. when modulated 60 percent b. when an…

A: As per the policy we are supposed to answer only the first 3 questions. Hence plaese post the last…

Q: 6.19 Obtain the equivalent capacitance of the circuit in Fig. 6.54. 35 μF Figure 6.54 40 μF 10 με 10…

A: Given a circuit Asked to find the equivalent capacitance seen from the terminals a,b

Q: For the circuit shown below, thevenin voltage at terminals a-bis 50 www 0.51, 1A 50² ba ob 10 V

A: Given circuit-     To find- Thevenin voltage.

Q: The circuit shown in the figure to the right has two input sources: vi(t) = 50 cos (20t – 75°) V…

A:

Q: Reactive power in a RL parallel circuit equals the power generated by  A. the resistor of the…

A: It is given that: parallel RL circuit

Q: 4. Given a carrier power of 10kW, verify that the total transmitted power remain the same as the…

A: Given information, Carrier power is Pc=10 kW. Modulating index is mf=0.25. We need to verify that…

Q: A cell of internal resistance 0.2Ω is connected to two coils of resistances 6Ω and 8Ω respectively,…

A: The question is emf of the cell.  Networks concept.

Q: 2-3. +Prove the identity of each of the following Boolean equations, using algebraic manipulation: B…

A: The given Boolean expression can be reduced to the required expression by using the Boolean…

Q: 1. a. Determine the thermal voltage for a diode at a temperature of 20°C. b. For the same diode of…

A:

Q: In a BFSK system, the carrier frequencies are separated by Rb , where Rb is the data rate in b/s. If…

A:

Q: Consider the following ODEs modeling causal LTI systems at initial rest, with input x(t) and output…

A: According to the question,

Q: A current sheet K = 16 ax A/m flows in the region -2 <y<2m in the plane z=0. Calculate the amplitude…

A: We need to find out magnetic field for given current sheet at given point .

Q: QA) a. Sketch the output v. and determine the dc level of the output for the network of Fig. 1. b.…

A: The output of the circuit is based on the conduction of the diode. If the diode is in forward bias…

Q: 9. A 1-MHz, 40-V peak carrier is modulated by a 5-kHz intelligence signal so that m = 0.7. This AM…

A: We need to find out the power in different components of modulated signal .

Q: Please complete the Q trace for the supplied signals shown below CLK J K Pre Cir r

A: Given, We need to plot the timing diagram for the output Q.  Here assuming rising edge  clock. i.e…

Q: A radio broadcast antenna is located at the top of a steep tall mountain. The antenna is…

A: It is given that: P=6kWf=104.3 MHz

Q: Required each problem: ● ● ● Equivalent Circuit Diagram Given Required in the problem Solution 3. A…

A:

Q: 2. A transfer function is characterized by the graph below. What is V_out for an input voltage of…

A:

Q: Required each problem: ● Equivalent Circuit Diagram Given Required in the problem Solution 5. A 40…

A: We need to find out the power delivered by armature for given generator .

Q: (b) An aperiodic signal defined below is the input signal to a system is sampled at 4000Hz rate:…

A:

Q: As being an electrical engineer you could join the Institution of Electrical and Electronics…

A: Yes, As being an electrical engineer we can join the Institution of Electrical and Electronics…

Q: 11.36 Find the complex power for the following cases: (a) P = 4 kW, pf = 0.86 (lagging) (b) S = 2…

A: In this questions We need to determine the complex power of the given questions  We know  Complex…

Q: For the aperiodic signal (that consists of one period of a sinusoid with a DC-offset): +2sin (2π…

A: Given: An aperiodic discrete-time signal is given as xsn=3+2sin2πf0n,0≤n≤N0-10,elsewhere where…

Q: Thinking about prime movers that are in Ontario's power system, how can the speed of the prime mover…

A: 1) In engineering, a prime mover is an engine that converts fuel to useful work.  2) So anything…

Q: 7.2 Convert each signal to the form (a, b, c, d, e}. *(a) u[n] - u[n- 4] (b) u[n] -2u[n-2]+u[n-4]…

A: To write the given signals in given format we can use the graphical representation.

Q: A balanced 3 phase star connected load draws power from a 400 V supply. Two wattmeter's indicate…

A: We need to find out input power and power factor for given two watt meter method .

Q: find the power factor Find the power factor 4Ω ww ( -j2Ω j5Ω -j2Ω

A: It is given that:- pf = ?

Q: 7) List the similarities and differences between the tone() function and the analogWrite() function.

A: 7. Differences- Depending on the kind of output being used, the analog notation may change.…

Q: 6. . The phase voltage of a 3-phase voltage source is 120 V. It is supplied to a star connected load…

A:

Q: 3- How large can the rms delay spread be, for a binary modulated signal BPSK with a bit rate of 25…

A: Solution (3) -  Given,For a binary modulated signal BPSK,Bit rate, Rb=25 kbpsandFor a 8-PSK…

Q: 6Α 40 Ω + Vo Δια 7 ) 30 V

A:

Q: Q2/1 f(t) = u(t) e Find f^-1 Cos (ut) EI

A: In this question we need to find a Fourier transform of the given signal.

Q: What is " Ifs " ?

A:

Q: Recall the equation of the Z-parameters -- V₁ 1 [H = V₂ Z21 Z22 U₁ Determine the Z-parameters (up to…

A: We need to find out the Z parameters for given circuit .

Q: Variation of critical clearing time with respect to inertia constant H is given below. H( MJ/MVA) 2…

A: Critical clearing angle and Critical clearing time in Transient stability In the case of single…

Q: Q1 Use Matlab as much as possible to perform the following tasks. You must submit the Matlab…

A: 1) Given polynomials are  a) p1 = 2s5-3s4+4s3-s2+3s b) p2 =-s6+5s3-s2-10 We need to determine the…

Superposition Theorem

The superposition theorem is applied to linear systems. For such systems, the output from two different inputs equals the sum of the outputs from each input separately. On applying this theorem many times we get the output from any number of inputs equal to the sum of the outputs from the individual inputs separately.