5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft.

5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
QUESTION 7 A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
The following drive system is used to raise a load at constant velocity. The motor rotational speed is 1000 rpm, and the rotational speed of the drum is 200 rpm. The efficiency of the gear box is 0.85. The efficiency of the drum is 0.95%. The moment of inertia of the motor (input shaft) is 0.5 kg.m², and the moment of inertia of the drum (output shaft) is 0.75 kg.m². Calculate: (1) The total (equivalent) moment of inertia of the drive system referred to the motor shaft. (2) The developed mechanical power on the motor Drum, 0.5 m diameter shaft. 1000 Kg Motor Gearbox
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8, and is 3D printed such that it has a yield strength in shear of τy = 2500 psi. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3. Note that circular tooth thickness, t, at the pitch circle is π / (2P). Repeat for a gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20 ksi). Only do the part for the 6061 gear do not do it for the 3D printed gear
Q2/ Two mating involute spur gears of 20* pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on cach wheel is such that the path of approach and the path of recess on cach side are half the maximum possible length each, find: i) the addendum for pinion and gear wheel, ii) the length of arc of contact, iii)the maximum velocity of sliding during approach and recess. Assume pinion to be driver.
Hello sir How are u Sir i hope you will solve the question The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The driving sprocket has 10 teeth and driven sprocket has 30 teeth. If the pitch radius of the driven sprocket is 250 mm and the centre to centre distance between the two sprocket is 400 mm, find the pitch and length of the chain
Match the items in columnsI and II. Column I P. Addendum Q. Instantaneous center of velocity R. Section modulus S. Prime circle Column II 1. Cam 2. Beam 3. Linkage 4. Gear (a) P-4, Q-2, R-3, S-1 (b) P-4, Q-3, R-2, S-1 (c) P-3, Q-2, R-1, S-4 (d) P-3, Q-4, R-1, S-2
To fear Tô rear wheel wheel Planet gears i. The tooth numbers for the automotive differential shown in the figure are N2 = 26, N3 = 68, N4 = 12, N5 = N6 = 20. The drive shaft turns at 1200 rev/min. a. What are the wheel speeds if the car is traveling in a straight line on a good road surface? b. Suppose the right wheel is jacked up and the left wheel resting on a good road surface. What is the speed of the right wheel?
Question 1: The figure shows a 16T 20° straight bevel pinion driving a 32T gear, and the location of the bearing centerlines. Pinion shaft a receives 2.5 hp at 248 rev/min. Determine the bearing reactions at A and B if A is to take both radial and thrust loads. On-Screen Keyboard Esc 1 3. 4 5 6.
A four-part mechanism like this one, if it is known the length of O2A (link 2) is 5 cm (link 3) is 4 cm (link 3) and the length of the bo4 (link 4) is 5.5 cm (5 in.). At the a point working the p = 50 Newton style with the sustric orientation of the horizontal line is 200 look for styles that are going on and torque on link 4.