5. Draw the sketch of the following cross section of channel and indicate the specifieddimensions.a Semi-circular section with radius r = 3.0mb Rectangular section : b=4.0m, and d = 2.0mC Trapezoidal section : Bottom width b = 3.0md = 2.0mDepth :Side Slope : 2 horizontal to 1 verticali. Calculate the area (A), wetted perimeter (P)and the hydraulic radius (R) of eachchannel.ii. If the discharge of these three channels are equal to 6.0m/s, determine the velocityof water flowing of each channel and identify which channel has the highest value ofvelocity 2, the lowest value of velocity ?

Answered: Image /qna-images/answer/97c37c4f-91ee-4fcb-b916-ae8172d6924a.jpg

5. Draw the sketch of the following cross section of channel and indicate the specified dimensions. a Semi-circular section with radius r = 3.0m b) Rectangular section : b=4.0m, and d = 2.0m C Trapezoidal section : Bottom width b = 3.0m Depth : Side Slope : 2 horizontal to 1 vertical d = 2.0m i. Calculate the area (A), wetted perimeter (P)and the hydraulic radius (R) of each channel. ii. If the discharge of these three channels are equal to 6.0m/s, determine the velocity of water flowing of each channel and identify which channel has the highest value of velocity 2, the lowest value of velocity ?

5. Draw the sketch of the following cross section of channel and indicate the specified dimensions. a Semi-circular section with radius r = 3.0m b) Rectangular section : b=4.0m, and d = 2.0m C Trapezoidal section : Bottom width b = 3.0m Depth : Side Slope : 2 horizontal to 1 vertical d = 2.0m i. Calculate the area (A), wetted perimeter (P)and the hydraulic radius (R) of each channel. ii. If the discharge of these three channels are equal to 6.0m/s, determine the velocity of water flowing of each channel and identify which channel has the highest value of velocity 2, the lowest value of velocity ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.pdf > H.W: the velocity profile in pipe is v(r) = v(c)(1-) Where: v(c)=velocity at center of pipe =2 m/sec R= radius of pipe=1m r= distance from center to a point. If r.d=0.9 y =1.11x10-5 m²/sec Find shear stress at 0.2m from center and shear stress at 0.1m from wall.
Assume SN= 50 kN
3. What will be the variation in BMD for the diagram? [Assume | = 2m]. 10 KN B A a) Rectangular b) Trapezoidal c) Triangular d) Square
3. A thin-walled section has the shape shown in figure below. The outstanding legs have a slope of 3 vertical to 4 horizontal. Locate the shear center. 80 mm 80 mm NA 80 mm 80 mm
b ... oil d water A vertical rectangular plate is submerged half in oil (SG = 0.83) and half in water as shown. Determine the ratio of force exerted by water to that of oil. A 3.25 B) 3.21 C) No answer among the choices D) 3.29 E) 3.16
A built-up section consists of two miscellaneous channels MC 18 × 42.7 and one cover plate 12 mm x 500 mm. The channels are placed at 300 mm back to back with the flanges outstanding. a) Determine the Ina(x)- b) Determine the Inav)- Properties of MC 18 × 42.7: A = 8129.02 mm² tw = 11.43 mm d = 450 mm Ix = 230.59 x 106 mm* br = 100.33 mm ly = 5.99 x 10° mm* %3D tf = 15.88 mm x = 22.28 mm MC 18 × 42.7
please answer with a neat solution and provide all answersA curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w = 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m.Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer.Determine the vertical component of the hydrostatic force (in N) acting on the gate, indicate the direction by putting an U for upward and D for downward after your numerical answerDetermine the magnitude (in N) of the hydrostatic force acting on the gateWhat angle (in degrees) does the hydrostatic force F make with horizontal?
Q: A quarter circle gate AB of 1.5 m radius and 3 m wide, hinge at B, find the vertical force F exerted on A. 1m Water Hinge B Smooth boundary r= 1.5 m
Q:-A quarter circle gate AB of 1.5 m radius and 2 m wide, hinge at B, find the horizontal force F exerted on A. 1 m Water Hinge B. Smooth r= 1.5 m boundary
Problem III. Figure (a) shows a channel section that has an area of 3790 mm² and its moment of inertia about the x and y axes are lx = 25.3 x 106 mm* and ly = 1 x 10° mm“. Now, figure (b) shows a section where two of the same channel section in Fig (a) are riveted together. EI 14.8 mm (a) (b) Determine the radius of gyration about x and y axes.
A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes qn angle of 30° with the horizontal, the 1.2 m sides being the horizontal. a. what is the minimum lressure acting on the plane in kPa b. what is the maximum lressure acting on the plane kPa c. Determine the magnitude of hydrostatic force acting on either side of the plane in KN. Support your computations with correctly drawn and labrled pressure prism diagrams.
Q=0.2 m D=0x5₂ Z₂ = SSm Z₁=25m P₁ = 200. zo=20m Figure 2