5. A 100 MW hydro-electric station is supplying full load for 10 hours in a day. Calculate the volume of water which has been used. Assume effective head of water a 200 m, and overall efficiencv of the

5. A 100 MW hydro-electric station is supplying full load for 10 hours in a day. Calculate the volume of water which has been used. Assume effective head of water a 200 m, and overall efficiencv of the

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28P: For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be...

See similar textbooks

Related questions

Q: 3. A hydroelectric plant has a reservoir of area 2 sq. kilometres and of capacity 5 million cubic…

Q: An electrical motor is supplied from a three-phase ,50 Hz, 410 V system on-board a LNG carrier .When…

A: According to guidelines we need to solve only first three sub-parts. According to the question we…

Q: 1-4 (a) Draw a connecting diagram for the electric power system in your area including major power…

A: Transmission line- The transmission lines are used to transmit high voltage power from one point to…

Q: The SME food factory35 Kw capacity Suppose the annual cost of the capital spent is $4500 per year,…

Q: A transmission line has an actual impedance of 18 ohms, compute for the per unit impedance of this…

Q: A wind turbine gives the following data: Blade length= 51 m. Wind speed = 16 m/s Air density = 1.228…

A: The data given in the question are: Blade length=51m, Wind speed=ν=16m/s, Air density=ρ=1.228 Kg/m3,…

Q: A hydro-electric station has to operate with a mean head of 250 m and is supplied from a reservoir…

A: Given that H= 250 m A= 120 Km2 available rain off =50 % Annual rain fall = 100 cm =1 m capacity…

Q: 1. Explain the environmental aspects of coal based power generation with neat diagram. 2. Discuss…

Q: A man has a body resistance of 600 N. How much current flows through his ungrounded body: (a) when…

A: The solution can be achieved as follows.

Q: 5. A power station has a maximum demand of ?? MW, a load factor of 0.7, a plant capacity factor of…

Q: A 200 V per phase synchronous machine with resistance and synchronous reactance per phase of 1 Q and…

A: Given values are - Power factorcosϕ=1R=1ohmX=8ohmVt=200∠0oVoltI=10∠0oA

Q: 9. A hydroelectric plant has a reservoir of area 2 sq. kilometers and of capacity 5 million cubic…

A: capacity=volume =5million cubic meters H=head of water turbine=50m reservoir area, A=2 Km2…

Q: For a hydroelectric power station, calculate the turbo generator efficiency for a site which is a…

A: Output of hydro power station = 9.81× pho× discharge in m3/sec×height of the dam × efficiency of…

Q: A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal…

A: NONE of the given OPTIONS is correct

Q: The fuel inputs per hour of plants 1 and 2 are given as F1 = 0.2 P1 2+ 40 P1 + 120 OMR per hr F2 =…

A: Fuel inputs per hour of plants 1 and plants2. Find the power of each plants for economic load…

Q: Maria Cristina falls located at south has a height of 100 meters, it discharges at constant rate 2.5…

Q: A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal…

A: For this power system ,we choose the base value quantities same as rating of transformer. Base…

Q: The fuel-cost curves for a two generators power system are given as follows: C¡ (P1) = 600 + 15 · P1…

Q: In an undisturbed sea level condition airstream, the velocity of the flow is 600 ft/s. What is the…

A: It is given that: v1=600 ft/sv2=680 ft/s

Q: An area of an interconnected power system has two fossil-fuel units operating on eco- nomic…

A: Given C1=4P1+0.02 P12 0<P1≤100 MW8P1 P1>100 MWand C2=0.03…

Q: The fuel-cost curves for a two generators power system are given as follows: C (P1) = 600 + 15 · P1…

A: Given: C1P1=600+15P1+0.05P12C2P2=700+20P2+0.04P22PL=2×10-4P12+3×10-4P22-4×10-4P1P2 MWMarginal cost,…

Q: First Quiz A generating station has a maximum demand of 10 MW. Calculate the cost per unit generated…

A: The solution for the given plant's cost per unit can be achieved as follows.

Q: 1.4 A single-phase 480020° V bus is connected to a single-phase 100KW motor operating at a lagging…

Q: j0.1 2.0+j0.5 j0.4 j0.2 1.01 3.

A: This question is from "Power System". Under which we are going to find out the "Y-parameter of the…

Q: Q4/ Find the values of incremental fuel costs using LaGrangian multipliers for the two-unit system…

Q: load of the persons and infiltration in the room are 5100 W and 3400 W respectively; the air is 1250…

Q: While designing the distribution to locality of one lac population with medium dense load…

A: While designing the distribution with medium dense load requirement or to locality of one lac…

Q: 2. Calculate the continuous power that will be available from hydroelectric plant having an…

Q: Which component represents Y axis of load duration curve ? a Time of a day b. Peak Demand C Power…

A: Choose the correct option Which component represents Y axis of load duration curve?

Q: Example 8. A hydro-electric power station has a reservoir of area 2-4 square kilometres and capacity…

Q: The current to a pure resistance load is given by the equation i=10sin314t. Calculate the…

Q: Example 9 : The weekly discharge of a typical hydroelectric plant is as under : Day…

A: Average daily discharge=500+520+850+800+875+900+5467=713m3/sec According to the data given, days on…

Q: Q1. The yearly load duration curve of a certain power station can be approximated as a straight line…

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: Q4/ Find the values of incremental fuel costs using LaGrangian multipliers for the two-unit system…

A: Answer -

Q: A system consists of two plants connected by a tie and a load is located at plant two. When 100MW…

A: . A system consists of two plants connected by a tie and a load is located at plant two. When 100MW…

Q: (a). Differentiate the following as applied to hydropower generation i). High head development ii).…

A: Hydropower Generation- Hydropower generation is a process which is used to hydraulic turbine convert…

Q: 8. Calculate the continuous power that will be available from hydroelectric plant having an…

Q: Q1. The yearly load duration curve of a certain power station can be approximated as a straight…

A: Given 2 generators of 20 MW 1 generators of 10 MWMaximum load=80 MWMinimum load=40 MW

Q: A generating station has a maximum demand of 55MW, a load factor of 63 %, a plant capacity factor of…

A: In this question load factor , use factor, capacity factor ,maximum demand given....We have to find…

Q: 11. A hydroelectric power station is supplied from a reservoir having an area of 50 km2 and a head…

A: The hydroelectric power is the cheapest method of producing electricity. The potential energy of…

Q: The weekly discharge of a typical hydroelectric plant is as under: Day Sun Mon Tues Wed Thurs Fri…

A: Given, The weekly discharge of a typical hydroelectrical plant is as under, Plant has an effective…

Q: Q.2 (a) Discuss the reasons of present power crisis in India. How can the conditions be improved?

A: The explanation is as follows.

Q: If some AC load is turned on and consumes a current =0.4 A, and electrical power produced from…

Q: Q2/ The following demands in a power plant as: Group 1: 300 kW between 7 A.M. and 8 P.M Group 2: 150…

Q: what is the power loss in the line in megawatt (MW)?

Q: A single line diagram of a system is shown in Fig. All the values are in per unit on a common base.…

A: The given circuit is shown below: V=1 p.u.P=1p.u.cosϕ=0.8 lagging

Q: The reservoir area of the hydroelectric power station is spread over an area of 4000 square…

Q: 1. To demonstrate the theoretical method of transforming delta networks to wye network, or…

A: As per our guidelines, we are supposed to answer only one question. Kindly repost other questions as…

Question

100%

Need Solution through 15min

5. A 100 MW hydro-electric
station is supplying full load for
10 hours in a day. Calculate the
volume of water which has
been used. Assume effective
head of water a 200 m, and
overall efficiency of the
station as 80O%. *
1.293 x 10 -3 unit volume
1.293 x 10 +6 unit voume
2.293 x 10 -3 unit volume
0.293 x 10 -3 unit volume
O 2.293 x 10 +6 unit volume

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

b) A power station has the following daily load cycle as Figure Q1(b) below: Time in Hours 6-8 8-12 12-16 16 20 20-24| 24–6 Load in MW 90 40 60 20 20 20 Figure Q1(b): Daily Load Cycle i) Plot the load curve i) Plot the load duration curve i) Determine energy generated per day
For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be the base kVA and 2400 V as the base voltage for the generators.
Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
The single-line diagram of a power system in shown in the figure. The reactance data for the power system shown in the figure in per unit on a common base are as follows; T1 T2 3 2 4 G1 G2 Item X1 X2 X0 G1 0.100.100.05 G2 0.100.100.05 T1 0.25 0.25 0.25 T2 0.25 0.25 0.25 Line 1-20.300.300.50 1. Draw the positive, negative and zero sequence networks and obtain the Thevenin equivalent circuits 2. Find the fault current for a single line to neutral (SLG) fault as shown in Bus 1.
The data of the power system shown in the figure: X= 1.2 p.u. X= 0.15 p.u. 20MVA G1, G2, G3: T, Т, Тз: L1, L2, L3, L4: Ls: Draw the reactance diagram marked on it all the reactance's in per-unit. 11 KV 30MVA 11/66 KV 66KV X= 400 66KV X= 202 T1 L (G1 T3 Ls L4 美 T2 G3 G2
1- Which of the following statement is TRUE ? a. True power is measured in VA b. All the power drawn by a resistive circuit is converted to useful work c. Apparent power and Reactive power are always equal d. True power cannot be measured using wattmeter 2- Which of the following statement is TRUE ? a. Bulb is considered as inductive load b. Loads such as transformers and motors consume reactive power with current waveform lagging the voltage c. Loads such as transformers and motors consume power with current waveform leading the voltage d. Heating element is example of capacitive load
. Frame a priority list for supplying a load up to 1000 Mw in the given power plantsPlant 1 : FI = (7 + 0.003 PI) 103 k-cal/Mw-hr.P1= 500 MWPlant 2 : F2 = (7.5 + 0.002 P2) 103 k-cal/Mw-hrP2 max = 400 MWPlant 3 : F3 = (8 + 0.004 P3) 103 k-caI/Mw-hrP3 max = 200 MWThe fuel costs at the plants are given byCPI = I. I Rs/kcalCP2 = 1.05 Rs/kcalCP3 = 1.2 Rs/kcal
Problem 5 For two electrical system shown in Figure 5, use cyclic currents to derive a complete mathematical model for each of the electrical systems. Ri. Rz ca) Cz (6) ERZ RI
Two synchronous generators G1 and G2 are connected to a power transformer Trand a transmission line as shown below. The system details are as follows:G1: 80 MVA 11KV X” = 20%G2: 60 MVA 11KV X” = 20%Tr. 100 MVA 11/132KV X” = 12%T.L. Xline = j140 Ωa) Draw the system diagram in per unit on a base power =100 MVA and a basevoltage =11KV at the generators side.b) Calculate the three-phase balanced short circuit current (If ) at busbar 3 inAmpere at the high voltage side and at the low voltage side of the transformer. c) Calculate the fault level (MVA)sc in MVA at the high voltage side and at thelow voltage side of the transformer
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power is O 4000 VA O 8000 VA O 6000 VA O 2000 VA
9. A central station is supplying energy to a community through two substations. Each substation feeds four feeders. The maximum daily recorded demands are: POWER STATION. 12,000 KW Sub-station B.. 9000 kW . 2820 kW 1500 kW 4000 kW 2900 kW Substation A 6000 kW .1700 kW 1800 kW Feeder 1 Feeder 1 Feeder 2. Feeder 3. Feeder 4. Feeder 2. Feeder 3. Feeder 4. 2800 kW 600 kW Calculate the diversity factor between (1) substations (if) feeders on substation A and (ii) feeders on sub- station B. |) 1-25 () 1-15 (il) 1-24]
A central station is supplying energy to a community through two substations. Each substation feeds four feeders. The maximum daily recorded demands are : POWER STATION. 12,000 KW Substation A . 6000 kW Sub-station B . 9000 kW . 1700 kW Feeder 1. Feeder 2. Feeder 1 2820 kW Feeder 2 . 1800 kW 1500 kW Feeder 3 . . 2800 kW Feeder 3 . 4000 kW Feeder 4. Feeder 4. Calculate the diversity factor between (i) substations (ii) feeders on substation A and (iii) feeders on sub- station B. 600 kW 2900 kW