Please solve question 4.44 attached below, Thank You! 4.44 Consider the 2-degree-of-freedom system defined by:[1929] * + [1² 3-33x = 0Use modal analysis to calculate the response of the system to the initial conditions: x = 0and Xomm

The equation of 2 degree of freedom is defined by The initial condition are

Answered: 4.44 Consider the 2-degree-of-freedom…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): A. Use Laplace transform of the differential equation to determine the transfer function of the system.
Using similarity transform we transform a system into a different system. Select one: True False
Find the ditferential equation from the transfer of the function for the Giving following system and draw the block diagram of the system. x(s) H(s) u(s) 0.5s + 1
Response using Laplace transformation.
Example For the system shown, the equations of motion are given by m₁x₁ + cx₁ + kx₁ Cx₂ = 0 m₂X₂ + CX₂ cx1 = F Use state space method to reduce the equation of motion into a system of 1st order differential equations. www m₁ m₂ f
Q5 Obtain Unit-Step Response of First-Order Systems: C (t). R(S) C(s)
Response using matlab.
Equation of motion of a suspension system is given as: Mä(t) + Cx(t) + ax² (t) + bx(t) = F(t), where the spring force is given with a non-linear function as K(x) = ax²(t) + bx(t). %3D a. Find the linearized equation of motion of the system for the motion that it makes around steady state equilibrium point x, under the effect of constant F, force. b. Find the natural frequency and damping ratio of the linearized system. - c. Find the step response of the system ( Numerical values: a=2, b=5, M=1kg, C=3Ns/m, Fo=1N, xo=0.05m
4. A model for an airplane's pitch loop is shown below. Find the range of K that will keep the system stable. Can the system every be unstable for positive values of K? Commanded pitch angle + Controller K(s + 1) (s + 4.85) 1 Aircraft dynamics s + 10 s² +0.6s +9 Gyro Pitch angle
6. The electro-mechanical system shown below consists of an electric motor with input voltage V which drives inertia I in the mechanical system (see torque T). Find the governing differential equations of motion for this electro-mechanical system in terms of the input voltage to the motor and output displacement y. Electrical System puthiy C V V₁ R bac (0) T bac T Motor - Motor Input Voltage - Motor Back EMF = Kbac ( - Motor Angular Velocity - Motor Output Torque = K₂ i Kbacs K₁ - Motor Constants Mechanical System M T Frictionless Support
4G I. 3:22 A moodle1.du.edu.om Consider the 3 degree of freedom robot manipulator as shown in the figure Link 3 Länk 2 Trint 1 The objective is to find the kinematics inverse of the robot Px=0.9 m, Py=0.6, L1=1.5m, L2=1.5m and qz= 2 rad The value of cos(q2) is equal to Choose... + The positive value of sin(q2) is equal to Choose... + The value of q2 in rad is Choose... + The value of qı in rad is Choose... + The value of q3 in rad is Choose... +
2) Consider the transfer function of a system below. Please find the range of K for stability: K G(s) = (s + 3)(s + 8)(s + 10)(s + 1) + K

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

4.44 Consider the 2-degree-of-freedom system defined by: [2]+[233] x=0 3¾ X= Use modal analysis to calculate the response of the system to the initial conditions: x = 0 1 and Xo = mm 2