3rd: A simply supported 12-m span beam, 300-mm wide by 550-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. What maximum service uniform live load can the beam support in addition to its own weight if allowable tensile stress in concrete 0.5 x

3rd: A simply supported 12-m span beam, 300-mm wide by 550-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. What maximum service uniform live load can the beam support in addition to its own weight if allowable tensile stress in concrete 0.5 x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN
Question A pre-stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
A rectangular beam has a width of 285 mm and an effective depth of 520mm. It is reinforced with 4 – 36 mm ø bars having fy = 430 MPa. If he compressivestrength of the concrete is 28MPa, find the following a. Location of the neutral axis from the top of the beam.b. Stress of the steel.c. Ultimate capacity of the beam?
21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is 4.2E6 psi and the Poisson ratio is 0.15. 16in 16in What is the normal stress along section b-b? a. -15.625 psi b. -7.81 psi c. -2.60 psi d. -11.04 psi
The maximum load of 200 KN was applied on a cylindrical specimen of concrete. Find the split tensile strength in MPa. Take depth as 150 mm and length as 300 mm.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
SITUATION A: A T beam has a property shown below. fy = 420 MPa, f'c = 35 MPa %3D %3D and Es =200,000 MPa effective width = 1200 mm 100 тm 550 mm 450 mm (3060 mm²) 300 тm 2. What is the distance of the neutral axis from the extreme compression concrete in mm?
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.