3.4 The load on a cantilever beam of length L consists of a load Pat the tip (free end) and a distributed load wacting over the entire length. Both Pand ware random variables. The length is assumed to be deterministic, and its value is 6 ft. The statistical parameters of Pand ware as follows (1 lb = 4.448 N; 1 ft = 0.3048 m): Hp = 4000 lb Vp = 10% Hu = 50 lb/ft V = 10% A. Calculate the mean and standard deviation of the internal bending moment at the fixed end. B. Calculate the mean and standard deviation of the internal shear force at the fixed end. C. If both Pand w are normal random variables, what is the probability that the bending moment at the fixed end will exceed 29 k-ft (1 k-ft = 1.356 kN-m)? D. If both Pand w are normal random variables, what is the probability that the shear force at the fixed end will exceed 5000 lb?

3.4 The load on a cantilever beam of length L consists of a load Pat the tip (free end) and a distributed load wacting over the entire length. Both Pand ware random variables. The length is assumed to be deterministic, and its value is 6 ft. The statistical parameters of Pand ware as follows (1 lb = 4.448 N; 1 ft = 0.3048 m): Hp = 4000 lb Vp = 10% Hu = 50 lb/ft V = 10% A. Calculate the mean and standard deviation of the internal bending moment at the fixed end. B. Calculate the mean and standard deviation of the internal shear force at the fixed end. C. If both Pand w are normal random variables, what is the probability that the bending moment at the fixed end will exceed 29 k-ft (1 k-ft = 1.356 kN-m)? D. If both Pand w are normal random variables, what is the probability that the shear force at the fixed end will exceed 5000 lb?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Deflection Given: the beam cross-section shown have the following cross-sectional properties f'c = 4000 psi n = 8 Find Instantaneous Deflection and long-term deflection ( 4 year life; 30% sustained load).
A mass of 50 kg achieves a velocity of 2 m/sec when it strikes the solid squared (side = 60 mm) beam ABC, Asume that the mass of the aluminum beam can be neglected and calculate: (a) the deflection of the beam at the point of impact in units of mm (b) the maximum stress due to impact in units of MPa B 2 m 1 m Show all calculations and box the final answers. Also, input your answer for part (b) in the answer box below.
Strength of materials - ENGR 3321 The answer should be: 13.8 MN/m2; 5.94 cm from tip of T
Question 1 (1 mark) Find the ratio of section modulus of two beams of same weight and length if the first beam has a solid circular cross-section of diameter D and second beam is a circular tube of outer diameter D and inner diameter d. (2 marks)
Calculate the shear modulus for a given cylindrical metal speciman and test results of T = 1500 N ⋅m, L = 20 cm, D= 5 cm, and ϕ = 0 02 rad . Can you tell what the material is?
As a construction engineer, you are asked to evaluate the maximum allowable vertical shear Vmax that may act on the hollow stainless-steel beam having a rectangular cross section as shown in Figure Q4. Discuss the effect of geometry on the shear stress developed in the beam | 20 mm y 350 mm V 10 mm- -10 mm 1 30 mm E 200 mm
to prevent excessive deflection of a cantilever steel beam, a tension rod is attached to its end. Determine the deflection before the tension rod is attached Given: BeamLength: 3m uniformly distributed load(at full length) = 2Kn/m Stell Beam Properties: A=1900 sq.mm lx=5,12X10^5 mm^4 E=200 GPa
The cross-section of the beam in the picture is welded from two flat steel 100x20x2000 mm. So L = 2000 mm. The material is S355 J2 G3 (EN 10025). What is the certainty compared to the following? q0 = 19.4 kN/m Correct answer 4.07
daterm - Attempt 1 %3D Item 6 Consider the beam shown in (Figure 1). Suppose that w = 410 N/m Part A Determine the magnitude of reaction at A. Express your answer to three significant figures and include the appropriate units P門A FA- Value Units Submit Request Answer Figure < 1 of 1 Part B Determine the x and y components of reaction at B using scalar notation. Express your answers using three significant figures separated by a comma. B. If vec B. By= 3 m 3 m- Submit Previous Answers Request Answer
ES IS lio cuts ebsite ahman [² Question 14 of 25 A lead cube has a total mass of 80 kg. What is the length of its sides if SG = 11.3? Select the correct response: Slunef 18.23 cm 19.2 cm 15.29 cm 12.32 cm 20.3 cm < Previous CHAPTER bar CHAPTER 213 ppt CHAPTER 1(4)(2).ppt
A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below. The intensity of the distributed load is 100N/mm. b = 6.25mm and c=6.25mm. A y Parameter L a d 0 L B 777 Description Beam length T Width of the flange Height of the web Yield stress |←0 →| Value 250 80 75 250 y Units mm mm mm MPa You are tasked with ensuring the beam can withstand the applied loading. To do this you must: a) Calculate the centroid for the given cross-section. Your value of y should be measured from the bottom of the section. Determine an expression for Q (statical moment of area) for the given shape. The expression(s) for Q should be in terms of the variable, y, measured from the bottom of the section.
The vertical shear force of 20 KN is applied to the beam of cross section shown.If beam dimension H is 66 mm, determine the shear stress acting along the neutral axis of the beam section. Present your answer to 5 significant figures in N/mm2. Number NA_ H H H ΝΑ H H H