Can someone explain this problem step by step, please 3. Use figure 2 for answering questions a-f.a)b)c)d)115 V rms60 HzVppris10:1eeeeeeeeee410DisD₂D₁OutputC+50 uFAll diodes are IN4001.www.R₁2.2 kWhat is the PIV for each diode?Find the average output voltage, VdcFind the peak-to-peak ripple voltageFind the ripple factor

For the given figure answer the following question: PIV for each diode. Average output Voltage,…

3. Use figure 2 for answering questions a-f. a) b) c) d) 115 V rms 60 Hz Vpis 10:1 eeeee 00000 Dis D₂ D₁ D₁ 50 µF Output All diodes are IN4001. R₁ 2.2 k What is the PIV for each diode? Find the average output voltage, Vdc Find the peak-to-peak ripple voltage Find the ripple factor

3. Use figure 2 for answering questions a-f. a) b) c) d) 115 V rms 60 Hz Vpis 10:1 eeeee 00000 Dis D₂ D₁ D₁ 50 µF Output All diodes are IN4001. R₁ 2.2 k What is the PIV for each diode? Find the average output voltage, Vdc Find the peak-to-peak ripple voltage Find the ripple factor

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: For the single phase fully controlled bridge is connected to RLE load. The source voltage is 230 V,…

Q: Derive the circuits for a three-bit parity generator and a four-bit parity checker using an…

A: Parity checker: It checks the process that makes sure accurate data occurs between the nodes during…

Q: Three-bus system network consists of TWO generators located at buses 1 and 2 and TWO loads located…

A: The Given is V1=j0.5∠0° and V2=1.03, PG2=2pu SD2=0.5+j0.2 and SD3=0.6-j0.25 The Given Matrix is…

Q: At equilibrium the Fermi level at the Drain and the Fermi level at the Source are: Select one: O…

Q: Q4:- Find the Thévenin equivalent circuit for the network external to the resistor Rt for the…

A: Given data,

Q: B The output of the following circuit is: 5V O (AB)' 4 ΚΩ Ο 51 ο ον ig iBx2 ΚΩ Οι OIB 2 ΚΩ O Y = AB

A: For the above given electrical circuit we need to compute it's output voltage under the given input…

Q: The reactance data for the power system shown in Figur in per unit on a common base is as follows:…

A: Positive-sequence impedance network for Problem- The positive-sequence impedance network is…

Q: Q4/:- For VCO-LO circuit block, if the message signal is the sine wave as shown in the figure below…

A: Given: message signal, m(t): F=1T=110-3=103 Hzwhere F is frequency of signalT is time…

Q: Q2-A-For VCO-LO that represent FM-TX if frequency of the carrier signal at -5 volt. Calculate the…

A: It is given that:

Q: Determine the following for the network shown: a. VGS b. lp C. VDS d. VD e. VG f. Vs + 1 ΜΩ 2V G +…

Q: 10. A signal is band limited to 3.6 and three other signals are band limited to 1.2 kHz each. These…

Q: The Fermi level of the P-Type semiconductor is located at O a. none of the other answers O b. The…

Q: When the energy is equal to the Fermi level, the Fermi function is equal to: O a. 0.5 O b. none of…

Q: 1.What is the difference between bipolar junction transistor and field effect transistor? Explain…

A: NOTE: As per our company guidelines we are supposed to answer only one question. Kindly repost…

Q: A three phase, 220V, 50Hz, rpm mesh connected synchronous motor has a synchronous reactance of 4…

A: Given data : Line voltage VL=220V Line current iL=30A Synchronous reactance Xs=4Ω Phase current…

Q: c) Compute the no load line voltage of a star connected 4-pole alternator for the following data:…

A: Given data, The flux per pole =0.12Wb, Slot per pole per phase = 4 Conductor/slot = 4, Two-layer…

Q: Simplify the Boolean function F(w, x, y, z)=Σ (0, 2, 4, 6, 8, 10, 11).

A: We need to simplify the Boolean function

Q: a) Sketch the output voltage for the following networks: R

A: The output of the circuit can be obtained by considering the state of the diode and then by using…

Q: b) Explain what will happen to the Fermi level at the source contact and the drain contact in the…

A: Fermi Level : The Level in between the valence and conduction band is known as the Fermi level, when…

Q: How many resistors are there in the hybrid pi model? 0 1 02 04 none of the other choices 05

A: Hybrid pi model: A circuit model for examining transistor small-signal performance is the hybrid-pi…

Q: A transmission line has the following line constants R=0.1Ω/ km, L=1.26 mH / km, C = 0.009 μF / km…

A: Given data, C=0.009μF/kmL=1.26mH/kmR=0.1Ω/kmG=0 Let, f=50Hzω=2πf =2π×50 ≅314rad/sec

Q: Suppose that the electricity consumption in your home last month was 354 kWh. In your contract with…

A: Given data, Consumed Units=354kWh Rate=11.3 cents per kWh Fixed Charge=$15.63

Q: In the circuit given below, R= 9 ΚΩ. Using mesh analysis, find the value of vo 30 V R 20 V (+ 5 ΚΩ 4…

A: Given circuit,

Q: An interaction between two elementary particles causes an electron and a positron to be shootout…

A: Given data, r=100 fm = 100×10-15 m

Q: A load of 240 +j 120 is connected to a source of 480 V with a phase angle of 30°, through a…

A: Given :A load ZL=240+j120 Ω is connected to a source voltage:V=480∠30° V through a transmission line…

Q: B) For the circuit shown below, the switch is opened for a long time, at t=0 it is closed. i) Find…

A: Given,

Q: 11. A speech signal is sampled at a rate of 8 KHz, logarithmically compressed and encoded into a PCM…

Q: 3.) (Based on Neamen, Ch. 10 Checkpoint #5 and #6) (a) Describe in words what is meant by…

A: MOSFET stands for Metal Oxide Semiconductor Field Effect Transistor. It is voltage controlled device…

Q: 18. If the arrows indicating the instantaneous direction of current are properly drawn on a position…

A: The instantaneous value of current : instantaneous current represents the sinusoidal wave of current…

Q: Information system is PCM using 8levels quantization, if the signal is given as V(A) = 8 Сas 8rt v…

A: Given, PCM system has Number of quantization levels(L) = 8 Signal is V(A) = 8 cos(8πt) Sampling rate…

Q: A parallel circuitcomprisestwo branches, (i) a coil of resistance 20 Ω and inductance 0.07 H and…

A: Given, A parallel circuit comprises two branches, (i) a coil of resistance (R1)= 20 Ω and…

Q: Any values for dynamic characteristics are indicated in instrument data sheets and only apply when…

A: Any values for dynamic characteristics are indicated in instrument data sheets and only apply when…

Q: 20. If you stub a motor winding, you A. reinforce the insulation. B. form phase-pole groups.

A: Insulation in slots is no need to change or reinforce. If motor winding is stubbed then it should…

Q: /rite the required equation of the frequency response H(w) of the Ideal LPF ith drawing.

A: LPF: stands for low pass filter. It is a electronic circuit which allows the low frequency…

Q: Simplify the following functions, and implement them with two level NAND gate circuits: (A, B, C,…

A: It is given that: F(A, B, C, D)=AC′D′+A′C+ABC+AB′C+A′C′D′

Q: In the system

A: Given data, G1(s) = p, G2(s) = 1(s+5)

Q: The D-MOSFET circuit though has a much lower input impedance than a similar JFET configuration. True…

Q: Q4) A 220 V d.c. shunt motor has an armature resistance of 0.5 ohm, and runs at 850 rpm., When…

Q: 2.) (Based on Neamen, Ch. 10 Checkpoint #9 - #11) (a) Sketch the cross section of n and p channel…

A: MOSFET stands for metal oxide semiconductor field effect transistor. It has high input resistance…

Q: (a) Using block diagram reduction method or Mason's Gain Formula, find the simplified transfer…

Q: semiconductor is n or p type, device is operating in accumulation, deplet 1 charges do each of the…

A: The semiconductor is p-type and the operation of devices in inversion mode.

Q: 7) For the sequence {1, 0, 1, 0}, IDFT will be None of the above {0.5, 0, 0.5, 0} {1,1,0, 1} {0.5,…

A: Given data : The sequence is xk=1,0,1,0

Q: 2.In digital modulation the carrier is one: A) binary wave B) high continuous wave frequency C)…

A: Given The digital modulation..

Q: A 220 Kv 50 Hz three phase transmission line consists of 1.4 cm radius conductors spaced 2 m apart…

Q: Diode turns OFF if the applied voltage polarity is Select one: O a. None of the answers b. opposite…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: (b) For maximum output, the Q-point must be: 1. Near saturation. 2. Near cut-off. 3. midpoint…

A: 1) If Q-point is near to saturation then +ve clipping of input signal. So no maximum output. 2)…

Q: 1. What is a cold solder in electronics? 2. What will happen if there is a cold solder? 3. What is…

A: Soldering is process of joining a metal parts in order to form a bond. The device used is called as…

Q: Using 64×8 ROM chips with an enable input, construct a 512×8 ROM with eight chips and a decoder.

Q: Consider the differential amplifier shown below with RB = 50KQ and Rc = 10KQ and assume the BJT…

A: The Given is differential Amplifier RB=50kΩ and RC=10kΩ To assume the BJT Parameters for Q1,Q2,Q3…

Q: An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. d. What is the error made…

Concept explainers

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.

Question

Can someone explain this problem step by step, please

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
Sketch i agains v to scale for the circuit. Assume 0.6 V for all diodes in the forward-bias region.
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
In each of the ideal-diode circuits show below V1 is a 1kHz, 10-V peak sine wave. Sketch the wave form resulting at V0. What are its positive and negative peak values?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee