3. The viscosity of liquids can be measured through the use of a rotating cylinder viscometer of the type illustrated in Fig. P1.3. In this device the outer cylinder is fixed and the inner cylinder is rotated with an angular velocity w. The torque T, required to develop w is measured and the viscosity is calculated from these two measurements. Develop an equation relating μ, w, T, e, Ro and Ri. Neglect end effects and assume the velocity distribution in the gap is linear.

3. The viscosity of liquids can be measured through the use of a rotating cylinder viscometer of the type illustrated in Fig. P1.3. In this device the outer cylinder is fixed and the inner cylinder is rotated with an angular velocity w. The torque T, required to develop w is measured and the viscosity is calculated from these two measurements. Develop an equation relating μ, w, T, e, Ro and Ri. Neglect end effects and assume the velocity distribution in the gap is linear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The physical model of a pipe containing water with kinematic viscosity o = 0.804 × 10-6 ™* has been built in the scale of in a laboratory. i. Find the ratio of velocity of water in the main pipe with kinematic viscosity of 8 = 2.79 x 10-4 m? to the model. ii. Discuss the difference in the velocities of the model and main pipe.
Helium at 20 ° C has a viscosity of 1.97 E-5 kg/(m ∙ s). Usethe data of Table A.4 to estimate the temperature, in ° C, atwhich helium’s viscosity will double.
As shown in Fig. 1.12, a horizontal interface 0-0 exists between two immiscible liquids. The dynamic viscosity of these two liquids are 0.14 Pa sand 0.24 Pa s respectively. The thickness is d1 0.8 mm and d2 1.2 mm respectively. Assuming that the velocity gradient is linear. Find theforce F required to push a bottom area A 1000 cm2 wood board to movewith velocity v0 0.4 m/s along the surface?
The physical model of a pipe containing water with kinematic viscosity has been built in the scale of in a laboratory. i. Find the ratio of velocity of water in the main pipe with kinematic viscosity of to the model. ii. Discuss the difference in the velocities of the model and main pipe.
Q1/ The angular velocity 2 of a car wheel was found to be a function of its height H as compared to the car height L, diameter D, the number of blades N, wind speed V, and density of air p. Find appropriate pi groups for this problem when viscosity effects are neglected.
Example 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is posted
Consider a propeller spinning in air. The thrust produced by the propeller is given by T. The density of the air is p. The forward velocity of the air is V. The diameter of the propeller is D. The rotational velocity of the propeller is n. The dynamic viscosity of the air is u. Using Buckingham's pi theorem, find the non-dimensional formulation of T = f (p, V, D, n, µ). Note that the non-dimensional quantities are not sensitive to multiplicative inverses, i.e. and 2 have the same meaning, as does multiplication by a constant, for example, and 2 imply the same non-dimensional group. T pVD V nD T f( PµD pV V nD T pV VD nD =5( T pnD pD V O O
Q1/ The angular velocity n of a car wheel was found to be a function of its height H as compared to the car height L, diameter D, the number of blades N, wind speed V, and density of air p. Find appropriate pi groups for this problem when viscosity effects are neglected.
Q1. A concentric cylinder viscometer is driven by a falling mass M connected by a cord and pulley to the inner cylmder. Annular gap of width a and height H has been filled with liquid to be tested. The speed of the falling mass is Vim. Develop an algebraic expression for the viscosity of the liquid. Evaluate the viscosity of the liquid using M= 0.1 Kg, R=50mm, H=80 mm, r-25mm, =0.20mm and Vim = 30 + ww XX Cord Puliey,
plz help me with this one , i would appreciate it if you can help me now. A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that has a diameter of 1 m that filled with oil that has a viscosity of 8x10-3 N.s/m2 What is the shear force that acts on the circumference of the piston (N)? Assume the variation in velocity of the oil is linear.
C1 (a). A lubricating oil having the dynamic viscosity of 0.056 poise and specific gravity of 1.17. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. C1 (b). The capillary effect in a glass tube of 2.8 mm diameter, when immersed in (1) water and (2) mercury are 7.7 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a). (i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m3/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and specific gravity of 1.11. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3,(iii) the kinematic viscosity in stokes, and (iv) the specific volume in m³/kg. C1 (b). The capillary effect in a glass tube of 2.6 mm diameter, when immersed in (1) water and (2) mercury are 7.4 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a).(i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m³/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m