3. The tank shown has a parabolic curve gate at the bottom right side of length h perpendicular to the paper. The parabola has a vertex at the center of the hinge A. The parabola is defined by the equation in the X-Y coordinate system as shown. Neglecting the weight of the gate and the vertical reaction at the bottom end B of the gate, show the following if the unit weight of the liquid is y. Liquid surface 27 (a) The location of the vertical component is 26 124 3 hinge Р h from the y axis is (b) The magnitude of the horizontal force P just to prevent the opening is yh³. 27 -h. 26

3. The tank shown has a parabolic curve gate at the bottom right side of length h perpendicular to the paper. The parabola has a vertex at the center of the hinge A. The parabola is defined by the equation in the X-Y coordinate system as shown. Neglecting the weight of the gate and the vertical reaction at the bottom end B of the gate, show the following if the unit weight of the liquid is y. Liquid surface 27 (a) The location of the vertical component is 26 124 3 hinge Р h from the y axis is (b) The magnitude of the horizontal force P just to prevent the opening is yh³. 27 -h. 26

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. From the given figure shown, the cylinders have equal diameters. a. give the reaction at A b. give the reaction at D c. give the reaction at C 40KN 20KN 30KN D 50 B.
Solve for part b in full step by step solution thanks
The polyvinyl chloride bar is subjected to an axial force of 900 lb. If it has the original dimensions shown, determine the value of Poisson’s ratio if the angle u decreases by Δu = 0.01° after the load is applied. Epvc = 800(103) psi.
Q2. A thermo gate consist of an aluminum plate AB and a magnesium plate CD, each having a width of 15.0 mm and fixed supported at their ends as shown in Figure Q2. If the gap between them is 1.5 mm when temperature is T= 25.5 °C, (a) Determine the temperature, T required to just close the gap. (b) Determine the axial force in each plate when the temperature T becomes 100°C. | Assume bending or buckling will not occur. Given Е,3 68.9 GPа, Е— 44.7 GPa. am w a = 24 (10-6)/°C,Co = 26 (10-6)/°C 10 mm 10 mm в с 600 mm 400 mm Figure Q2
The cage system shown in the figure is made of EC rod. The Flow Limit of the material is 180 MPa and the Safety Coefficient is 4 is desired to be. Accordingly, the circular cross section EC rod Calculate the diameter.
A square plastic bar (length Lp, side dimension sp = 193 mm) is inserted inside a hollow, square, cast iron tube (length Lc = 400 mm, side sc = 200 mm, and thickness tc = 3mm). (a) What is the required initial length Lp of the plastic bar so that, when it is compressed by some force P, the final length of bar and tube are equal to legnth Lc, and, at the same time, the gap between plastic bar and cast iron tube is closed? (b) Compare initial and final volumes for the plastic bar. Assume that Ec = 170 GPa, Ep = 2.1 GPa, vc = 0.3, and vp = 0.4.
1. A bar with a constant cross section A is fixed at both ends. The bar is made of two different materials, that are joint together at point C. a) What are the reaction forces, if an external force F is applied at point C? b) Determine the normal force that is caused by a pure heating by AT. Given: Es Eat ast - 1 SAINT LC = 3, Steel Aluminiun
A bar is loaded both mechanically and thermally. it is fixed at both ends. Determine the displacement of point C, and support reactions at A and B. Use two 1-D bat elements for your solution. Check your answer with strength of materials solution
The aluminum tube AB of cross section has a fixed support on the base and is supported by a pin at the top of a horizontal beam supporting a load Q = 200 kN. Determine the required thickness t of the tube if its outside diameter for 100 mm and the necessary safety factor in relation to Euler buckling for n = 3.0 (assuming A = 72 GPa). I know the answer, but I cannot understand the critical charge formula. I don't know why to use the constant 2.046 in the formula, can you please show me?
The topic is all about thermal stress. Use pen and paper to solve. Show the conversion in the solution. The discussion: δT = α ∆T LδT = α (Tf −Ti) L Where:α = coefficient of thermal expansion in m/m°C or in/in°C∆T = change in temperature (Tf – Ti) (+ ∆T = expansion) (- ∆T =contraction)L = Length of the member in mm or in P.S. show the relationship in deformation
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %3D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. 6 ft 3ft VAVAVAVAVA Ib f Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of (Igx) Vahue of ybar (9) Location of the Hydro. Force measured from the water surface of the gate inclined (yel Ib ft ***answer Hydrostatic Force Fon the box below: Answer: 1311.03 The correct answer is: 1022.1
A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.