3. The circuit shown is represented in the frequency domain. Given the line current Line = 0.57614 - 75.88° A, determine Psource, the average power supplied by the source, PLoad, the average power delivered to the load. Hint: Use conservation of power to check your answers. 120/ 0° V Isource 1:5 June Source transformer 1 www 402 j10 Ω line 5:1 transformer 2 Load www 1002 j40 02 load

3. The circuit shown is represented in the frequency domain. Given the line current Line = 0.57614 - 75.88° A, determine Psource, the average power supplied by the source, PLoad, the average power delivered to the load. Hint: Use conservation of power to check your answers. 120/ 0° V Isource 1:5 June Source transformer 1 www 402 j10 Ω line 5:1 transformer 2 Load www 1002 j40 02 load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Given Zo-j407 2, R₁143, R6317 52 and a 0.04, what is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ ww Answer: Zc Zc R₁ Use up to 2 digits after the decimal point if necessary in your answer below VL-28020 V TR
A three phase power transformer having a line voltage ratio of 400 V to 33 kV is connected in star-delta. The C.T.s on 400 V side have current ratio as 1000/5. What must be the C.T. ratio on 33 kV side. Assume current on 400 V side of transformer to be 1000 A. C.T. secondaries in delta p 5A oooo oooo 5√3 A -0000 0000 0000 0000 Star-delta transformer 0000 5√3 A vooo னள். m reeee p C.T. secondaries in star 5√3 A 0000
A generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:20), and a transmission line (R=20 Ohm and X-60 Ohm), the base values for this system are chosen to be 480 V and 10 kVA at the generator. The line base impedance is: Select one: O a. None of the above O b. 9216 Om O c. 1.25 Ohm O d. 13 Ohm O e. 520 Ohm
The average value of sinusoidal varying voltage is more than its r.m.s. value. Select one: O True O False Which of the following formula is CORRECT? a. E= - L d0/dt O b. E = - N dl/dt O . L= NI / O O d. W = 0.5 12L In a step down transformer, number of turns in the primary winding is lesser than the number of turns in the secondary winding. Select one: O True O False
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
2. The pu impedance of a circuit element is 0.15. If the base kV and base MVA are halved. Then the new value of pu impedance of the circuit element is A. 1.2 C. 1.1 3. The pu impedan B. 1.0 B. ambient tempera- ture D. 0.8 E. none
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
The equivalent circuit of a transformer is shown below. Given VLs= 2400 20° and IL= 62.5 L-36.8°. Calculate the value of Vi and li
5. A power-supply transformer has a secondary voltage if the primary is connected to a 120 V rms source? 6. Determine the peak and average power delivered to RL in figure. turns ratio of 5:1. What is the 2:1 120 V rms 220 N ell lelll
The turn ratio and type of transformer required for the circuit shown in figure, where the average value is 15.9 and the input voltage is 120v rms: reeeeeee 0.294 step up O 0.147 step down eeeeeee 0.294 step down 2:1 step down O 5:1 step down Other: R₁
The rated voltages of a single-phase transformer are 2000 V and 200 V in its primary and secondary respectively. The shunt impedance can be modelled with a resistance of 14000 ohms in parallel with a reactance of 1100 ohm, both refer to primary side. The primary and secondary series impedances are (0.12+j 0.35) ohms and (0.0012+j 0.0035) ohms respectively. A load is connected to the secondary side of transformer, draws 810 KVA with a lagging power factor of 0.85. The load voltage is same as rated voltage, that is 200 V. ▪ Use per unit method for analysis and find the voltage on primary side in pu.
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he