3. If a wall has a total height of 4m and a width of 25 ft, find the number of 10 by 20 by 40 cm CHB, the horizontal reinforcement at every 2 layers and its vertical reinforcement spaced at 60 cm on center. Commercial length of steel bar = 10 mm ø by 9.0 m (Use Area Method and Unit Block Method)

3. If a wall has a total height of 4m and a width of 25 ft, find the number of 10 by 20 by 40 cm CHB, the horizontal reinforcement at every 2 layers and its vertical reinforcement spaced at 60 cm on center. Commercial length of steel bar = 10 mm ø by 9.0 m (Use Area Method and Unit Block Method)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
To calculate the reinforcement ratio p, assume a 7 in. slab with an effective depth of 6.0 in., with No. 6 (No. 19) bars spaced 5.5 in. center to center. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area bar size size (soft) (in) (mm) (in) (mm) No.6 0.167 0.249 0.250 6.35 0.05 32 No. 10 0.375 = % 9.53 0.11 #3 0.376 0.560 %3D 71 #4 No.13 0.668 0.994 0.500 12.7 0.20 129 #5 No.16 1.043 1.552 0.625 % 15.9 0.31 200 #36 No.19 1.502 2.235 0.750 = % 19.1 0.44284 #7 No.22 2.044 3.042 0.875 = % 22.2 0.6087 #38 No.25 2.670 3.973 1.000 = % 25.4 0.79 510 %3D No 29 3.400 5.060 1.128 % 28.7 1.00 645 # 10 No.32 4.303 6.404 1.270 1% 32.3 1.27 819 # 11 No.36 5.313 7.907 1.410 % 35.8 11 1.56 1,006 # 14 No.43 7.650 11.384 1.693 1% 43.0 2.25 1,452 # 18 No.57 13.60 20.239 2.257 1% 57.3 4.00 2,581
Given data: Beam width, bw = 300mm Tension Steel bars = 8-25mm ᴓ equally-placed in two layers Effective depth to centroid of entire reinforcement, d = 512.5 mm Effective depth to centroid of outer layer of reinforcement, dt = 537.5 mm Concrete Strength, fc’ = 42 MPa, Steel strength fy = 415 MPa Using NSCP 2010: Determine the location of the neutral axis of the section. Determine the value of the strength reduction factor ᴓ for flexure. Determine the flexural strength of the section in kNm.
Provide solution and illustrations. Use three decimal places A rectangular reinforced concrete beam exposed to weather has a width of 300 mm and a total depth of 600 mm. The diameter of the bar to be used for reinforcement is 16 mm. fc’= 31 Mpa and fy = 276 Mpa. Determine the required number of bars for reinforcement.
Design a monolithic concrete slab indicated below. The floor slab is to carry a service live load of 2.7KPA uniformly distributed over its surface and service deadloads of 1.1KPa for floor finish and 0.72KPa for ceiling. Use fc = 21MPA, fy = 276 MPa, Unit weight of Conc = 23.54KN/m³. Sketch the reinforcement detail. -4.5000+3.0000-4.0000- -4.5000- 5.2000 SLAB 1 6.4000 7.0000 3.0000
Given the following properties of the reinforced concrete beam shown, f, = 60,000psi and fe = 4,000 psi , compute the effective area of the 12 in. 3 in. concrete subjected to the compressive stress 0.85 f . 27 in. 33 in. 30 in. 4 #11 3 in. 18 in. 168.406 in.2 O 104.816 in.2 2 140.861 in. 186.408 in.2
Considering the nominal shear stress on concrete is f = 0.83 MPa. Calculate the allowable max spacing for 2-legged 10 mm stirrups? Use simplified calculation for Vc. Beam dimensions are 397 x 754 mm. Effective cover of steel reinforcement = 70 mm fy = 275 MPa Spacing should be in multiples of 10 mm. NOTE: USE STORED VALUES IN YOUR CALCULATION
Problem 2: A reinforced concrete beam has a width of 300 mm and a total depth of 550 mm. Effective cover to centroid of tension bars is 60mm. Compressive reinforcement (if required) will be placed at d’ = 60mm. f’c = 21 MPa and fy = 415 MPa. The Follow 2010/2015 NSCP provision and use ? = 0.90 for flexure. a.) Determine the required area of steel reinforcement, As, if the beam carries a factored moment of 79 kN-m. b.) Determine the required area of steel reinforcement, As, if the beam carries a factored moment of 193 kN-m. c.) Determine the required area of steel reinforcement, As, if the beam carries a factored moment of 402 kN-m.
A singly reinforced beam will be provided with the reinforcing bars corresponding to 90% of the maximum reinforcement ratio specified in the ACI Code for a tension-controlled (i.e., underreinforced) design. The materials used have the following properties: ??′ = 4000 psi, ?? = 80000 psi, ?? = 0.002 Estimated the steel area ?? Sketch the stress and strain distributions in the beam cross-section. The diagrams should show the location of the neutral axis and the compressive/tensile forces acting on the cross-section Calculate the nominal moment strength ?? and the design moment strength ??? [in kips-ft] Briefly explain how the formula of moment calculation can be derived Assume that the design moment strength is less than the factored moment. Hence, compression rebars will be added. The effective depth is ?′ = 1.5′′. Determine the steel area of compression rebars ??′ so that the compression bars yield at the flexural failure Based on ??′ determined in part d calculate the nominal…
Minimum percentage area of HYSD reinforcement in a 150 mm thick water tank wall is (a) 0.16 (c) 0.23 (b) 0.20 (d) 0.24
Design the load bearing reinforced concrete wall shown if fc' = 3000 psi and fy = 60000 psi. For horizontal and vertical shear reinforcement: Use #4 rebar = 0.5" = 12 mm For vertical flexural reinforcement: Use #9 rebar = 1.128" = 28 mm Vu at the top = 100 kips Lw = 8 ft, hw = 15 ft, thickness of shear wall = 8 in