3. A simple beam has a 15 foot span and a W18 x 50 section. Determine the maximum bending stress and average shear stress due to two concentrated loads of 5000 lbs. each applied at the third points of the span and an uniform load of 2000 lbs./ft (this includes the weight of the beam) over the entire length of the beam. (15pts) 2000 lbs/ft 5 5000 lbs 5 5000 lbs 5 R2

3. A simple beam has a 15 foot span and a W18 x 50 section. Determine the maximum bending stress and average shear stress due to two concentrated loads of 5000 lbs. each applied at the third points of the span and an uniform load of 2000 lbs./ft (this includes the weight of the beam) over the entire length of the beam. (15pts) 2000 lbs/ft 5 5000 lbs 5 5000 lbs 5 R2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam is subjected to a uniformly distributed load. What is the maximummagnitude of the average shear stress in the beam, and where does it occur?
Determine the maximum bending stress (in psi) in the beam and its location as generated from the loading condition with the beam cross-section shown below. 2 kip/ft -5 ft- -5 ft 30 kip-ft -5 ft- B 12"- 6" AX
Calculate and plot the stress diagrams for the beam below. 7kN m 5 kN/m C B D= 3m + D/2 + D/2 -| 12KN
A simply supported beam of span 3.0 m has a cross-section 120 mm × 180 mm. If the permissible stress in the material of the beam is 10 N/mm², determine () тахітит udl it can сarry (ii) maximum concentrated load at a point 1 m from support it can carry. Neglect moment due to self weight.
A wooden log is to be used as a footbridge to span 3.50-m gap. The log is required to support a concentrated load of 30 kN at midspan and a uniformly distributed load of 20 kN/m throughout the span. If the allowable stress in shear is 0.7 MPa. 1. What is the diameter of the log that would be needed? Assume the log is very nearly circular and the bending stresses are adequately met. Neglect the weight of the log. 2. If the log is to be trimmed to have a square cross section, what shall be the resulting dimensions (Round off to the nearest whole number). 3. Compute for the maximum flexural stress of the beam loading.
attempt.php?attempt3D165240&page=D7 The timber beam is to be loaded as shown. If the ends support only vertical forces, determine the greatest magnitude of P that can be applied. Use allowable normal stress of 61 MPa and allowable shear stress of 700 kPa. m 150 mm T 30 mm yc=53.71 mm 120 mm I=19.162x10 mm 4. 40 mm Lütfen birini seçin: a. None b. 6.07 kN c. 3.48 kN d. 3.31 kN e. 5.79 kN
Q1/ A composite beam is made of wood and reinforced with steel strap located on its bottom side. It has the cross-sectional area shown in fig. if the beam is subjected to a bending moment of M=2kN.m, determine the normal stress at wood and steel. Take Ew=12Gpa and Est=200Gpa. 150mm Wood en 20mm Steel 150mm
Question 3 Determine the maximum bending stress in the steel beam in psi with the circular cross section. 400 lb 200 lb/ft D 2 in. -5 ft- -4 ft-
1. For the simply supported beam with a T-shape cross-section as shown below, a- Draw the shear and moments diagram of the beam. b- Determine the maximum normal bending stress and specify its location. C- If the beam made from two boards determines the maximum shear stress in the glue necessary to hold the boards together along the seam where they are joined. d- Determine the shear stress at point B. 4 m 6.5 kN/m 6m- Glue 150 mm 30 mm 150 mm 30 mm
Find the maximum flexural stress in the shown beam. 2000 ib M- 4800 hit Sin 3 t 6 ft T 3 t Ro
A simply supported beam of dimension 12 m x 45 mm x 65 mm. It carries a uniformly distributed load of 450 kN/m for entire span. Determine (a) Maximum stress due to bending and (b) Young's modulus of the material used for the beam, if it deflects 150 mm maximum at the mid of the span. Also find the maximum slope in the beam. (Enter only the values by referring the units given, Also upload your hand written answers in the link provided) Moment of inertia of the cross section of the beam in m4 : Young's modulus of the beam material in MPa is = Maximum bending stress due to bending in MPa is = The slope at the supports of beam in radians is
Determine the absolute maximum normal stress (in unit of MPa) in the beam with external loadings shown below. The beam has a uniform square cross-section with lateral size a = 0.2 m. Note: (1) the shear and moment diagrams can be calculated by either section method or graphical method; (2) there is a concentrated load at point A and a bending moment at point C. 20 kN w = 20 kN/m Mc = = 80 kN · m || В A¬Q C y 2 m 2 m 2 m