Answered: 23 Implement and draw a multi-range…

23 Implement and draw a multi-range voltmeter to obtain the voltage ranges of 0-5V, 0-20V, 0-50V, 0-100V. Im 3mA and Rm= 60 n.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Related questions

Q: A potentiometer is used to measure the voltage between two points of a dc circuit, which is found to…

Q: What is the internal resistance of a voltmeter having a 20 KiloOhm/V sensitivity and set on the…

A: The obstruction offered to the smooth flow of current is called resistance. When a potential is…

Q: Design a simple current mirror using a current of 1 µA and VGS of 1 volt.

A: Given that I=1μA, VGS=1V The basic constant current source current mirror is shown below.

Q: 8. A dc microammeter with an internal resistance of 250 2 and a full-scale deflection current of 500…

A: In this question, We need to calculate the unknown resistance R? If meter indicate the current I=…

Q: Calculate IR3 in mA of the circuit with R1=1228 ohms, R2=2326 ohms, and R3=3158 ohms and a supply…

A: Solution: Here, D acts as…

Q: there are 100 graduations in the scale of an ammeter with internal resistance of 0.18 Ω and intended…

A: We need to find out resolution and Shunt resistor for given ammeter

Q: voltage dividing potentiometer is used to measure an angular displacement. The angle if displacement…

A: Given total angle travel =355° degree The angle of displacement =60° Voltage of…

Q: RI = 80KN ww VT = 100V R2 = 80KN V )0-100V Range %3D What does the voltmeter read when it has a: A.…

Q: I CLASS DISCUSSION ITEM 8.3 Laboratory A/D Conversion Why is a 12-bit A/D converter satisfactory for…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Design a Multi-range Ammeter device that can measure the electrical current passing through the…

A: In this question , we will design multi range ammeter...

Q: +12V 4.7kQ 150KN 1MQ Vout VIC B = 180 3.3kQ

Q: Find the Total current flowing through D1 and D2 and D3 . Vs= 10v, R1=R2=R3=10kNThe three diodes are…

A: Given circuit, All diodes are silicon diode.

Q: A moving coil instrument gives full scale deflection with 15 mA. The resistance of coil is 5 Q. It…

Q: Suppose that the components of the circuit shown in figure below, have the following values: R1= 162…

A: given values are, R1=16Ω, R2=18Ω, R3=30Ω ,R4=9Ω, R5=4Ω Voltage across AB VAB=36R5R5+R4=3644+9true…

Q: A DC voltmeter has a sensitivity of 1000 ohm/volt. When it measures half of full scale what is the…

A: Given: Sensitivity(S)=1000ΩVoltS=1KΩ/Volt

Q: 2k Ohm JFET =16 V 1 M Ohm 2V Figure 8.4 Common Source Configurations

A: Find Vgs and Vd for the given JFET?

Q: how to find current ina circuit

A: In a circuit, current can be found by computing the values of resistance and voltage in the circuit.…

Q: 6- Design a multi range (0-5) mA, (0-8) mA, (0-10) mA, (0-25) mA and (0-50) mA ammeter using a 50µA…

Q: the range of voltmeter from (-10 to -30) volt, then the span of it (state 20-) a (state 40) b O…

A: Any voltmeter has an upper and lower voltage limit. the span of the voltmeter is the algebraic…

Q: What is the internal resistance of a voltmeter having a 10KOhm/V sensitivity and set on the 0-100V…

A: Let us find the internal resistance of the voltmeter on a full scale reading. The sensitivity of the…

Q: What is the Vref for Iref = 250 microamps in the circuit in the figure? What is R1?

Q: The value of a resistor R is to be determined using the ammeter-voltmeter setup shown in Figure…

Q: a) PMMC meter has (10MA) half scale current deflection and (1500) internal resistance. Use this…

A: PMMC stands for permanent magnet moving coil. It works only for Dc because PMMC measures average…

Q: The Voltage Drop will not depends upon the a. Length of the run O D. Voltage Drop Factor O c. The…

A: The formula for voltage drop In a line is, Voltage drop = current x impedance-----(1)

Q: 3. Explain how you would experimentally determine the value of RNonon in the circuit below. 250 3.5m…

A: Given circuit,

Q: A voltmeter is specified to have a range of 0 - 400V . if the inaccuracy is +/_5%. The measured…

Q: E,(s) Consider the electronic system shown in Figure 1. Obtain E,(s) C2 R2 ww R4 ww ww R3 ww RI E(s)…

A: In this question , we will find transfer function..

Q: Design a CT to measure a current of 2000A, if a ammeter of (0-20A) is to be used for the measurement…

A: Given: A CT to measure a current of 2000 A, for the measurement process an ammeter of (0-20 A) is to…

Q: DMM or CRO R1 R3 V1 4 AA battery box (~6V output) V2! R2 R4 Rin Figure 4

Q: Which of the following is the basic operating mechanism of a potentiometer? a. Potential divider O…

A: Potentiometer is work on mechanism of potential divider.

Q: What is the total resistance?

Q: Answer all questions in details (draw and derive all formulas) Q-1 : Analyze the circuit of the…

A: For the calculation of voltages at all nodes VE=VB+0.7 .......(1)VEC sat=0.2 VVC=VB+0.5…

Q: A galvenometer has full scale current of 20 (mA) and has a meter resistance of 2000 (ohm). To…

A: Given that RG = 2000 ohm Rsh = 200 ohm

Q: Find the Total current flowing through D1 and D2 and D3 . Vs= 10v, R1=R2=R3=10kQThe three diodes are…

A: Let V1 is node voltage.

Q: 2. A voltage dividing potentiometer is used to measure an angular displacement. The angle of…

A: Given total angle travel =355°degree The angle of displacement =60° voltage of excitation…

Q: For the network of Figure below, determine the range of Vi that will maintain VL at 8 V and not…

Q: . Design a multi range (0-1) mA, (0-10) mA, (0-20) mA and (0-30) mA ammeter using a 50µA PMMC meter…

A: In the circuit we are designing a multi range ammeter have 50 microampere and internal resistance…

Q: Q2: (a) If a for de is equal to 0.987 so determine the value of B for de. (b) Now if B for de is…

Q: 10 V A -10 V ΙΚΩ Si 10k2%

A: To Determine and sketch the output voltage waveform and the current flowing in the resistor for the…

Q: In the figure below, find the range of load resistance values that maintain a zener voltage of 10v e…

A: The solution is given below

Q: What is the equivalent resistance (in Ω) seen at the terminal of the 7.5V voltage source? (up to 2…

A: Equivalent resistance, Let us start from the rightmost part of the figure, 5Ω∥10Ω=5×105+10=3.333Ω…

Q: Write down the steps on how to Series Resistors Voltage Division

Q: Q4: Find the currents flowing in each of the diodes D1, D2, D3and D4 of the circuit in Fig 4. What…

Q: A0 to 150V voltmeter has accuracy of 2% of ful scale reading. The theoretical (true)expected value…

A: Given, Full scale value is, VF=150V The accuracy is, Accuracy=2% The true value is, True Value = 83V

Q: 79 To reduce the effect of a voltmeter upon thencircuit under test, we should decrease the…

A: To minimize the voltmeter loading, we can use an instrument with a high internal resistance.

Q: It is desired to measure a voltage of 80 V with a voltmeter with a full scale value of 500V.As a…

Q: Design a multi range DC voltmeter for the range of (0-5) V, (0-10) V, (0-50) V using a basic…

A: Given, Rm=100 Ω IFSD=1 mA where, Rm is the internal resistance and IFSD is the full scale deflection…

Concept explainers

Photoconductive Cell

Photoconductive cells are light-sensitive resistors in which resistance is inversely proportionated to light intensity when illuminated. These devices consist of a thin single-crystal or polycrystalline film of composite semiconductor materials. Cadmium sulfide (CdS) is used to make the most commercially available photoconductive particles which are sensitive to light in the visible spectrum. Other less commonly used substances respond to infrared light, but not to the visible spectrum. Such substances are lead sulfide (PbS), lead selenide (PbSe), and lead telluride (PbTe), and so on.

Question

23
Implement and draw a multi-range voltmeter to obtain the voltage ranges of 0-5V,
0-20V, 0-50V, 0-100V. Im 3mA and Rm= 60 n.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine and sketch the output voltage. R1 +10 V 1.0 kN D Vin 0 out 5v 5 v -10 V + Diodes are IN4001.
Find the current I in the following circuit assuming all diodes are silicon diodes. O 0.07 mA O OmA O 1 mA O 2 mA O 10 mA O 1.79 mA O 1.86 mA R = 10 k2 I E = 20 V- R = 10 k2 ype here to search DE
Q3/ a/ What is the function of the inductance L in a single phase halfwave thyristor? b/ A controlled full wave bridge rectifier has a source of 50 Sinwt with R = 10 and L = 20 mH find the d.c load current if a = 40° , then draw Vo and lo use %3D %3D 50 Hz freq. and ß = 1.1n
Write down the name of the circuit and draw both input and output voltage waveshapes for Vin=10V, and R1=1KHZ and both the diodes D1 and D2 are silicon diodes. R1 D2 VIN VOUT 4V E 6V
Zener Diodes: In the following diagram, Iz = 0.5 mA, Vz = 5, rz = 30 ohms. What is Vout? What is the current through D5? Current through D7?
4 1.0 k VS2 VSI 25 V 8 V Diodes D1 and D2 in the figure are assumed ideal, what is the current through the diodes? * D₁ B R www C
For the diode circuit shown below, indicate the ON/OFF condition for all the diodes given VA and VB values. Calculate Vout, Vx and all the currents that flow through the diodes. Summarize your result using a table. +4V VA VB VA OV OV 4V D₁ D₂ X 5ΚΩ D3 VB OV 4V 4V -2V 5ΚΩ VOUT
Assume each diode to be OFF when VĎ ≤ 0.7V and ON when VĎ >0.7V. Find iD1, D2, İD3, and vo in each diode circuit. Vos 10₂ K + 102 110, TO +5V + J03 - 1kn Vo Please show your work in full detail. Thank you. 1603 M 1ks
Determine the voltage waveforms across each half of the secondary winding and across RL when a 100 V peak sine wave is applied to the primary winding. (Si diode used) What minimum PIV rating must the diodes have? D +25 V ----- 2:1 +100 V IN4001 0- Vin oV -25 V -S RL 10 kf -100 V +24.3 V ---- IN4001 Vot 0- alll
Qʻ: Determine if the diode (ideal) in Figure is forward biased or reverse biased And find VD + 10V 2 k2 4 k2 V2 8 kN 6 kN ww
In the following circuit the diodes are 0.7 constant voltage model 10V Select one: C. m 10K a. None of the answers b. 2 diodes are reversely biased the 10K resistor can not have currents d. 2 diodes are forwardly biased
11 Exercises: Determine VO and Ifor each circuit in figures. Assume that each of the diode in these circuits has a forward voltage drop of 0.7 V. +2V -4V +5V D D₂ D₂ D₁ € V. 20 -4V +6V -21 tototot D₂ D₂ D₁ (b) +107 $2402 117 -87 +37 -SV 04040404 D₂ D D (0) -15V 2402 V.