For the A36 steel plate with staggered bolts and used as a tension member (see below), determine the nominal strength based on the gross area and then determine the nominal strength based on the net area (20 pts) For the A36 steel plate with staggered bolts and used as a tension member (see below),determine the nominal strength based on the gross area and then determine the nominal strengthbased on the net area.PL % x122"3"3"-3".3"-5"-2"4"4"2"34-in.-diameter bolts->

Answered: Image /qna-images/answer/b427c800-abe7-4bb9-907b-c052eec33e49.jpg

(20 pts) For the A36 steel plate with staggered bolts and used as a tension member (see below), determine the nominal strength based on the gross area and then determine the nominal strength based on the net area. PL % x12 2" 3" 3"- 3". 3" -5"- 2" 4" 4" 2" 34-in.-diameter bolts ->

(20 pts) For the A36 steel plate with staggered bolts and used as a tension member (see below), determine the nominal strength based on the gross area and then determine the nominal strength based on the net area. PL % x12 2" 3" 3"- 3". 3" -5"- 2" 4" 4" 2" 34-in.-diameter bolts ->

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Related questions

Q: Compute the block shear design strength of the tension member shown in the figure. The holes are for…

A: The block shear strength calculated as 82.51 kips. Please refer step 2 for the detailed solution and…

Q: USING LRFD, DETERMINE THE ff: 1. LOAD P that the angles can carry against tensile yielding in the…

A: Given : Breadth of the plate, B = 200 mmThickness of the plate, t = 10 mmDiameter of bolts, d = 20…

Q: A channel shape, C8 × 18.75, is used as a tension member. The channels are bolted to a 10mm-thick…

Q: Select the lightest C section that will safely support the service tensile loads PD = 65 k and P₁ =…

A: Reinforced concrete : Reinforced concrete, also known as reinforced cement concrete or…

Q: Q.2: Design a tension member (lightest C section) to carry the service tensile loads (PL=40k and…

A: determining the factored load PuPu=1.2D+1LPu=1.2×75+40=130Kminimum gross area Ag…

Q: 3. Select an A992 10-ft long channel member that can resist a service load of 128 kips (DL:LL=3:2).…

Q: Determine the design capacity of the given tension member. Assume that the slenderness requirement…

A: Answer We are given L 7 x 7 x 1 (Ag = 13 in2 , x=2.115 in) ASTM A36 (fy = 40 ksi , fu = 60 ksi) Bolt…

Q: Determine the design capacity of the given tension member. Assume that the slenderness requirement…

Q: Design of Tension Members. Determine the LRFD design strength and the ASD allowable strength of…

Q: A Channel C6x13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using…

A: Data Given: Channel Section = C6×13Bolt Diameter = 58 inchFy = 36 ksiFu = 58 ksiAg = 3.81 in2U =…

Q: Determine the LRFD design strength and the ASD allowable strength of the W16x31 shown including the…

A: Given W16×31 and Grade of steel = A992 for A992 steel, yield stress Fy = 50 ksi, ultimate stress…

Q: Determine the LRFD design strengths ØP and the ASD allowable strengths P/f of the following section…

A: Answer (a) Fy =345 Mpa, Fu = 450 Mpa Bolt = 22mm tf = 11.18 mm We know that Nominal block shear…

Q: 1.0 A double-angle shape is shown. The steel is A36, and the holes are for 12 mm diameter bolts.…

A: 1)

Q: An angle L150 x 90 x 12 of AS72 steel (F,= 350 MPa and F= 450 MPa) is used as tension member…

A: Given: Angle section: L150 x 90 x 12 of A572 steel g = 50 mm, for 150 mm leg is connected fy = 350…

Q: A plate 3⁄8 3 6 is used as a tension member to resist a service dead load of 12 kips and a service…

A: It is required to determine the factored load using LRFD method. Pu=1.2DL+1.6LL=1.212+1.633=67.2…

Q: A C8x11.5 single channel section us bolted to a gusset plate with M22 bolts. Assume A36 steel, 5.6…

Q: Select the lightest C6 channel shape to be used as a 12 ft long tension member to resist the…

A: Pu=1.20×PD+1.60×PL=1.2×20+1.60×32=75.2kCalculating min. area required1) Min. Ag=PuϕFy=75.20.9×36=2.3…

Q: A C8 x 18.75 is to be used as a tension member. The channel is bolted to a 3⁄8-inch gusset plate…

A: Solution Given Data C8 x 18.75

Q: Compute the net area of each of the given members. The built-up section shown in Fig. P3-8 for which…

A: Refer to AISC table 1-8 Section properties of the member WT15×45 The area of the member AWT is 7.07…

Q: Problem 5: A double-angle tension member, 2L 76 × 51 × 6.4 LLBB (Longer legs are connected back to…

A: Given Gross area =1.2 in2 Dead load =15 kN= 3.372 kips Live load= 6kN=1.3488 kipi

Q: A W10x45 with two lines of (3/4)in diameters bolts in each flange using A572 grade 50 steel is used…

A: Answer We are given bolt diameter = 3/4 in W 10 x 45 A 572 grade steel To determine the LRFD design…

Q: A C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown in Figure P3.2-3. If Fy =…

A: The design strength is reduction in the actual resistance of the member while considering the factor…

Q: Problem 2: Select the lightest C section that will safely support the service tensile loads (Dead…

A: Given:- The magnitude of the dead load = PD = 65 k The magnitude of the live load = PL = 50 k The…

Q: Using ASD, select the lightest double-angle tension member to resist a service dead load of 30 kips…

A: The given data is: Dead load, D=30 Kips Live load, L=90 Kips Yield strength, Fy=36 Ksi Ultimate…

Q: 2C10 x 20, of A572 grade 50 steel ½ - inch - diameter bolts REQUIRED: The total service load…

A: Given:- Two C10 x 20 channels are given The diameter of the bolts = ½ - inch The live load is 3…

Q: 3-21./ Determine the effective net area of the L8 X 4 x ½ shown in Fig. P3-21. Assume the holes are…

Q: Determine the effective net area of the L7 x 4 x1/2 shown in Fig. P3-21. Assume the holes are for…

Q: Fy= 50 Ksi, Fu= 65ksi Select the lightest W10 section available to support working tensile loads of…

A: Given : Fy= 50 Ksi, Fu= 65ksi Select the lightest W10 section available to support working tensile…

Q: Using ASD, select the lightest double-angle tension member to resist a service dead load of 30 kips…

Q: 3. Select an A992 10-ft long channel member that can resist a service load of 128 kips (DL:LL=3:2).…

Q: 1. A double-angle tension member, 2L 3 × 2 × 3/16 LLBB, of A36 steel is subjected to a dead load of…

A: For the given double angle tension member,

Q: Situation 2: A WT 8x13 of A992 steel is used as a tension member, The connection is with 7/8-in,…

A: WT 8×13 of A992 Diameter = 78inch Fy=50 ksi Fu = 65 ksi Ubs = 1.0

Q: ROBLEM: Using ASD, select the lightest double-angle tension member to resist a service dead load of…

A: Given data - Dead load = 30kips Live load = 90kips Bolts used = 7/8 inches, length of member =…

Q: Determine the lightest W 12 (A36) section suitable for a 8 m long W-shape member to carry an axial…

A: Solution Given: A36 steel fy = 36 ksi = 250 MPa fu = 500 MPa db = 20 mm P = 1900 kN

Q: What will be the strength of 20 mm diameter bolt of grade 4.6 (in kN) for the double cover butt…

Q: 3.5-1 Compute the nominal block shear strength of the tension member shown in Figure P3.5-1. ASTM…

A: Given:- The diameter of the bolts = 1 in The ASTM A572 Grade 50 steel is used The number of bolts =…

Q: ● Design a 11 ft single-angle tension member of A992 steel, to support a dead tensile load of 25k…

Q: Problem 01 Select the lightest W12 section available to support working tensile loads of Po = 120 k…

Q: Question 7: The tension member is a PL% x 5½ of A242 steel. It is connected to a %-in. thick gusset…

A: The given diagram is show below, To Determine The nominal block shear strength in tension member

Q: 2 in 4 in

Q: Q2) A double-angle shape, 2L6 x 6 x %8, is connected to a %-inch gusset plate as shown in Figure.…

A: Thickness(t)=6 mm, Steel type=A36, Diameter of bolts(d)=3/4 inches.

Q: Select a 30-ft long W12 section of A992 steel to support a tensile service dead load of 130 kips and…

A: Limit state design For Limit state design load factor expressions are: Pu = 1.4 D and Pu = 1.2 D +…

Q: Q3) Determine the total number of 4-inch, A325 bolts required for the tension splice in Figure. The…

A: The given figure is shown below:

Q: 3-27. AW18X 40 consisting of A992 steel and having two lines of 1-in Ø bolts in each flange. There…

Q: A single L8x6x1/2 (A36 steel) is used as a tension brace in a multi-story building. The 8 inch leg…

A: The area of the hole is equal to the product of diameter added with 1/8 inches and the thickness of…

Q: Select the lightest S section that will safely support the service tensile loads D = 85 kips and L =…

Q: 2. A double angle tension member, 2L3x2x1/4 LLBB of A36 steel is subjected to a dead load of 12 kips…

A: Given :

Q: 3. A 2L4x4x1/2(3/8 in. separation). ASTM A36, has one line of (3) 4-in. dimeter bolts in standard…

Q: SITUATION B. Given the connection below bolted with 7/8-in diameter bolts, solve for the design…

Q: Determine the design capacity of the given tension member. Assume that the slenderness requirement…

Question

For the A36 steel plate with staggered bolts and used as a tension member (see below), determine the nominal strength based on the gross area and then determine the nominal strength based on the net area

(20 pts) For the A36 steel plate with staggered bolts and used as a tension member (see below),
determine the nominal strength based on the gross area and then determine the nominal strength
based on the net area.
PL % x12
2"
3"
3"-
3".
3"
-5"-
2"
4"
4"
2"
34-in.-diameter bolts
->

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A PL ½ x 8 tension member is connected with six 1-inch-diameter bolts, as shown in Figure P3.2-2. The steel is ASTM A242. Assume that A, = A, and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. PL ½ x 8 o o o
Compute the tensile capacity for the ½ inch thick plate shown. The bolts are ¾ inch diameter high strength bolts. The steel is A36. 24" -P, 1 3"
A) The 3/4 in x 15 in plate has 4 rows (or horizontal lines) of bolts. Each row has 3 bolts. The bolt diameter is 7/8 in. Determine the gross area (Ag) and the net area (An) 3/4 15 O O O O O O Q O O 3" 3 27 3 784 Bolts Pet *
The splice plates shown in Figure 2 are 1/2-inch-thick. How many 7/8-inch-diameter, Group B bolts are required? The given load consists of 30% dead load and 70% live load. A36 steel is used. Threads are not excluded from the shear plane. 90 k Figure 2 ¾ in. 90 k
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
A Channel C6x13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using A36 steel with Fy=36 ksi and Fu=58 ksi. The gross area of C6x13 is 3.81 in? and Assume U =0.85 Using LRFD what is the design strength based on Tensile Rupture/Fracture 4 @ 2" a 1 1/2 Ob 3" Oc 1 1/2 " I d e C6 x 13 Round your answer to 3 decimal places.
3. Determine Rn based on bolt limit states. Slip critical connection is used for design and Grade 10.9 M22 Bolts with Class A surface. Check minimum edge distance and spacing with TSSDC 2016. All members are $355. There is no filler between plates and Du=1.0. Fy= 355 MPa; Fu=510 MPa; E=200000 MPa. All units are in mm. $R.=? 100 100 O 60 Geset Plate 75 Plate Gusset Plate $R.=? *20*201 Plate
Determine the allowable (ASD) tensile strength (kN) of a WT205X74.5 having two lines of M22 bolts as shown. There are four balts in each line, 75 mm on center. The yield strength of the steel is 345 MPa and the ultimate tensile strength is 483 MPa. Neglect the block shear strength.
Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates.
A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for ½/2-inch-diameter bolts. Assume that A₂ = 0.75A. a. Determine the design tensile strength for LRFD. b. Determine the allowable strength for ASD. Section 215 x 3 x 16 LLBB
Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in the plane of shear. The plates 3/8 x 7 and 5/16 x 7 are made of A36 (F,=58 ksi) steel. If live load to dead load ratio is 4, find the maximum service load that the connection can carry. A325X % in diameter bolts PL 3/8 x 7 PL 5/16 x 7 1.5 in 2 in 2 in 1.5 in 1.5 in 2 in 2 in 1.5 in
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB