2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm -80 mm Section A-A

2. Shown below are pieces of unsaid material. They are combined and locked in each other and a force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine the force P needed to fracture the materials in shear. 30 mm 30 mm -80 mm Section A-A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to…

A: Here, We need to calculate the average shear stress on the plate. diameter = 20 mm thickness = 8 mm…

Q: A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear…

A: Using relations

Q: An aluminum bar of solid circular cross section is twisted by torques T acting at the ends (see…

Q: The stress–strain diagram of the material can be approximated by the two line segments. If a bar…

Q: Given: A steel rod (A= 150 mm2) is stretched between two fixed points with a tensile load of 5000 N…

A: Given data:A=150 mm2 Load,P=5000 Nα=11.7×10-6/°CE=200 GPa or 200×103 N/mm2

Q: 3. (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: shear stress : Shear stress is a force that tends to distort a material by causing it to slip along…

Q: Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown…

A: Draw the state of stress diagram:-

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Given Stress in X direction for inclined plane = 31 Mpa

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

Q: The stress–strain diagram of the material can be approximated by the two line segments. If a bar…

A: The expression for the stiffness of the column material in the elastic region with the help of…

Q: Diameter of the metal bar, before and after load application was measured to be 100.00 mm and 99.99…

Q: Three rods, cach of area 250 mm2. jointly support a 7.5 kN load, as shown in Figure below. Find the…

A: My dear Given data Total hanging load Two types of materials. Area of cross section Youngs modulus…

Q: 7. Three rods of different materials are connected as shown in the figure. (a) Determine the maximum…

Q: ) For the given stress condition find: 1. Principal stresses and their orientation. 2. The stresses…

Q: A square plate of width o and thickness t is loaded by normal forces P, and Py, and by shear forces…

Q: Consider a cylindrical metal 6 mm in diameter and 50 mm long is pulled in tension. It is known that…

Q: Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.7 GPa. Bar (2) is a nylon…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: given- working stress σ=10 MPacross section area A=200 mm×b mmwhere,b=smallest allowable width To…

Q: Example 2.14 A plate 2 m x 2 m x 20 mm is subjected to stress o, 100 MPa (tensile) and o, = 50 MPa…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

Q: 1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: SHEAR STRESS: It is defined as the force, internal resisting force per unit area.The force acting on…

Q: Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon…

A: L=395mm A=900mm2

Q: Problem 1. A circular aluminum tube of length L = 400 mm is loaded in compression by forces P (see…

A: Given- L=400d1=60mmd2=50mm∈=550×10-6

Q: 3. The distribution of stress in an aluminum machine component is given (in megapascals) by Ox = y +…

A: The stress tensor is:

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: Ultimate stress is the safest stress taken within elastic limit. It is the ratio of ultimate stress…

Q: Which of the following is a deformation? Select one: a. Tension b. Shear c. Compression d. Strain

Q: The state of stresses in the x and y directions at a point in a given material is shown in the…

A: step 1-

Q: The state of stresses in the xand y directions at a point in a given material is shown in the figure…

A: step 1-

Q: 600 480 600 480 360 360 240 240 120 120 0.000 0.006 0.002 0.004 Strain 00 0.04 0.08 0.12 0.16 0.20…

Q: 1. A steel bar is subjected to the loads shown in the figure. Determine the total deformation in the…

A: When the material like steel bar or another object is under tension or compression the change in…

Q: a) For a beam loaded in Figure 2, express the shear force and bending moment in 21 and then…

A: Let's solve both question

Q: The state of stresses in the x and y directions at a point in a given material is shown in the fig…

Q: Osa 18° Taa /a 45° a 200 MPa 50 MPa

A: GIVEN: TO DETERMINE: The Normal stress on plane a-a CONCEPT: Angle substended by two planes on…

Q: An element in plane stress is subjected to stresses o = 5,780 psi, Gy (Consider only the in-plane…

Q: Given the following state of stress and material properties Ox = 10MPa E = 200GPa 0z = -15MPA v =0.2…

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

Q: The polymer bar shown in the figure below has a width of b = 42 mm, a depth of d = 97 mm, and a…

Q: The polymer bar shown in the figure below has a width of b = 59 mm, a depth of d = 90 mm, and a…

Q: The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of…

A: Following is the graph deduced from the given information in the table: Part a. Proportional…

Q: A circular rod and a 3/8-in.-thick rectangular bar are both made of a plastic material that has an…

A: Required Change in the diameter of the Circular Rod

Q: Define the following:a. Proportional limitb. Elastic limitc. Yield stress

A: a) Proportional limit - The proportional limit is indeed the greatest stress during which stress and…

Q: 80 (5) (6) 70 (3) 60- 50 40- (1) 30 20 10- 0+ Strain

A: For the stress-strain diagram, which region or point represents fracture?

Q: Problem 6 Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400…

A: Given - F = 8kN To find - Value of X

Q: Find the stress in each material at 65 °C

Q: Strength of Materials HOME WORK 3 – Combined For the assembly shown in the figure below, Determine…

Q: Define the terms shear stress and shear strain, illustrating your answer by means of a simple…

A: To determine diameter of bar under single shear and double shear

Q: Consider a rectangular specimen of aluminium has a dimension of 10 ?? × 12.7 ?? is pulled in tension…

Q: A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear…

A: As value of stress on element is given we xanapply the formula and get the principal stress values.…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: From the given question it is required to determine the smallest allowable width of the beam for the…

Question

2. Shown below are pieces of unsaid material. They are combined and locked in each other and a
force P is pulling each side. Assuming that the Shear stress for the material is 38 MPa, Determine
the force P needed to fracture the materials in shear.
30 mm 30 mm
80 mm
Section A-A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circuiar bars, one of brass and the other of steel, are to be loaded by a shear load of 30kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in the two materials must not exceed 50 MN/m² and 100 MN/m? respectively. [27.6, 19.5, 19.5, 13.8 mm.]
Q.1. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detemine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mm*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN'm2. Punchar 25 mm 26 mm 30 mm thick
Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mn*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN/m2. Puncher 25 mm 25 mm 30 mm hick
ASTEEL ܢܢܝܝܘ ܗ 25 KN ACOPPER a STEEL 2.8 m 3.6 m Three vertical rods of equal distance, each has a diameter of 20mm and supports a load of 25 KN as shown in the figure. Initially, all the rods are adjusted so that they share equal stresses. Neglecting any chance of buckling, and taking Es = 205 GPa and Ec = 100 GPa, determine the final stress in the steel when a further load of 20 KN is added.
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
b) Strain energy for truss AB. Enter your answer in J to 2 decimal places. Answer: Check Flag o c) Strain energy for truss BC. Enter your answer in J to 2 decimal places. Answer: Check
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
Prove each of the following equations separately 30 0x - 270 ([1-sin() sin(³9)] y Exy| Oxx 30 cos 1+ sin sin 270 30 K cos() sin() cos(32) K₁ x 2.70 Stresses near the tip of a crack in an elastic material. Crack FIGURE COS
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2