2. Given the following Ks= 10mg/l; q^=18mg/mg VSSa-d; Kd= .25d-1; Y= 0.7; Sᵒ=1,000mg/l; Q = 1000 m3/d; Xaᵒ=0. Determine the size of reactor required to achieve an effluent substrate concentration of 1 mg/l for a. a system with no input biomass b. a system with input biomass of Xo= 10 mg/l, 100 mg/l and 1000mg/l c. a system with Xo = 100 mg/l and effluent s = 0.1, 1, 10, and 100 mg/l

2. Given the following Ks= 10mg/l; q^=18mg/mg VSSa-d; Kd= .25d-1; Y= 0.7; Sᵒ=1,000mg/l; Q = 1000 m3/d; Xaᵒ=0. Determine the size of reactor required to achieve an effluent substrate concentration of 1 mg/l for a. a system with no input biomass b. a system with input biomass of Xo= 10 mg/l, 100 mg/l and 1000mg/l c. a system with Xo = 100 mg/l and effluent s = 0.1, 1, 10, and 100 mg/l

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question A direct runoff hydrograph due to a storm idealized into a triangular shape has a peak flow…

A: Given- Peak flow = 60 m3/s 25 hrs runoff base width = 72 hours, catchment area=777.6 km2 Runoff=?

Q: (113) The conduct of safe on-site construction operations is important to owners

A: To brief: The conduct of safe on-site construction operations is important to owners.

Q: What conclusion can be drawn from the results given below for a BOD analysis made using three…

A: Percent Waste BOD(g/m3)1 2002…

Q: Consider the truss shown in (Figure 1). Assume all members are pin connected. Suppose that P = 6.8…

A: Given: P = 6.8k

Q: Calculate the coordinates of points B and C of the connecting polygon

Q: What is the total weight of the following pieces of steel: 6-W8 x 28 that is 12'-6" long 4 W12x40…

A: Given Data Determine the total weight of the following pieces (W)

Q: 4 - A cantilever beam carries a tip load and moment applied at the tip, as shown in the figure. Find…

A: To determine The axial and shear stresses at point A, B, and C respectively. The representation in…

Q: 3- A steady, incompressible, two-dimensional velocity field is given by the following components in…

Q: (e) The main sanitary sewer is to serve a population of 76000. Calculate the size and slope of the…

Q: From the given figure below. Using Ranking Theory, the unit weight of concrete of gravity dam is 24…

A: Given:- The unit weight of the concrete = 24 kN/m3 The coefficient of friction between the concrete…

Q: Using equations of motion in cylindrical coordinates, a. Determine the angle between the extended…

A: Given data: Mass of ball bearing=2 kg Path equation, r=(1.5 θ) m Angular position of arm, θ=π8.t2…

Q: 5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an…

A: Answer Let us first calculate PrPc in order to know which interaction equation to be used LRFD Pr…

Q: The moisture content of soil in the root zone of an agricultural crop at certain stage is found to…

A: Given data- Moisture content=0.05, Field capacity=0.15 root zone depth=1.1 m Consumptive use=2.5…

Q: 2.2-lb steel tape is 99.98 ft long at 68° F v

Q: Q1. Compute ø for the following three cases: 650 mm 600 mm -350 mm- 44 4 fy=275 MPa f'c= 37 MPa 3…

Q: Question 5 From a topographic map, the areas enclosed by contour lines for a proposed dam are given…

A: Given data- Area enclosed by contour lines is given- To Find- The volume of impounded water using…

Q: The surface of a saturated clay deposit is located permanently below the groundwater table. The clay…

A: Given: The clay has natural water content = 43 % Specific gravity = 2.70 The vertical intergranular…

Q: METERS | FEET 76-250 61-200-013½" (75 HP) 1 Ø12%" (60 HP) THE Ø12" (50 HP) 46-150 al Ø11" (40 HP)…

A: From the graph, the red line represents the intersection. For 11716'' impellers, the horsepower is…

Q: Determine the controlling (lowest) net area of the member. X = 2.69 Y = (6-2.69)/2 Z=0,7 Y" -X Y" 5…

A: Controlling net area

Q: Q.2) Answer ONE from the following: A) Compute the coordinates of the traverse points Q, R, S, and…

A: Given:

Q: Replace the three forces acting on the rectangular solid with a wrench. Specify the magnitude of the…

A: Here, it is asked to replace three forces of Magnitude 10 n, 50N, and 15N with Magnitude of moment,…

Q: e) Bx (no need to indicate direction since this is an internal force) f) Net force in y-direction at…

A: A frame is hinged at A and C and an internal hinge is present at B To determine, The internal…

Q: Describe the physical state of soil with the following values of liquidity index: a) LI1.

Q: The level of water in the reservoir is 1.25 m. If there is a rainfall of 38 cm occurring in a month,…

A: Given data- Water level in reservoir = 1.25 m, Rainfall = 38 cm = 0.38 m, Class A pan evaporation=32…

Q: Define 'Shape factor'. Determine the shape factor of an I-section which is symmetrical about…

Q: Question 29 An A36 angle bar is used as a tension member connected on both legs with 20 mm . Given…

A: Given:- The steel used = A36 The value of s = 60 mm The angle used = L6×312×516 The gross…

Q: Q 8. Use moment are a theorems to find the slope and deflection at end C. Take E = 200 GPa, I =…

A: Given Data E = 200 GPa = 200 × 103 N/mm2 I = 80 × 106 mm4 Determine slope and deflection at end C…

Q: A vertical photograph of a flat area having an average elevation of 250 metres above mean see level…

Q: Using the compass (Bowditch) rule, adjust the departures and latitudes of the traverse given in the…

Q: What precisely is meant by the term "stress testing," and why is doing such testing advantageous in…

A: The question is a prompt to explain the concept of stress testing and its advantages.

Q: Problem 1 A 35 ft cantilever column has the following cross section A= 55.0 in², Ix= 3600 in*, and…

A: Given data: Column length, L=35 ft Gross area of section, A=55 in2 Ix=3600 in4, Iy=2800 in4 Pu=1000…

Q: Determine the change in length of a shaft if it experiences a temperature change of 0.059 °C. The…

A: Reference : Engineering mechanics, Thermal expansion of shaft, Strain relationship with temperature.…

Q: Q.1) Three forces and a couple moment are applied to an angle bracket as shown. The 50 lb force acts…

Q: Determine the reactions at the supports for the beam shown below. 4 kN/m 10 KN, 4 53m 12 m + 6 m…

Q: Calculate a) the position of the centroid b) the moment Ic, with respect to an axis passing through…

Q: Prob. 4 The figure below gives a cross section of a concrete dam. The subsoil is anisotropic and has…

Q: 4 - A cantilever beam carries a tip load and moment applied at the tip, as shown in the figure. Find…

A: Answer Let us first find the forces acting at a point A,B and C. Hx = 0 (Since no axial force…

Q: For what potential pitfalls may a public safety infrastructure development project be responsible?

A: There can be many potential pitfalls for which public safety infrastructure development project…

Q: Laboratory Problem Exercise #2 Given the figure and the following data: Determine (a) the width of…

A: Given:- The unit weight of the concrete, γc=2.4 T/m3 The coefficient of friction between the base…

Q: A steel rod of 30 mm diameter and 3 m length is subjected to an axial pull of 50 kN. If E = 200 x…

A: Given, Diameter (D) = 30 mm Length (L) = 3 m or 3000 mm Axial load (P) = 50 kN or 50000 N Elastic…

Q: There are three soils from left to right (1, 2, and 3). The soils have permeabilities ?1 = 0.09…

Q: Given the compound curve with the vertex V inaccessible, angles A and B are equal to 16°20' and…

Q: The two tangents intersects at an angle of 46-40 are to be connected by a reverse curve. The…

Q: What additional possibilities are there for confirming the truthfulness of the data while it is…

A: There are several possibilities for confirming the truthfulness of data while it is being collected…

Q: Given the two orthogonal projections of the object (top view and front view), identify the third…

Q: A 3mm Ø tube is inserted in water. Assuming a clean tube and the angle of contact with water is 0°,…

A: Given, Tube diameter (d) = 3 mm or 0.003 m

Q: Determine the lengths of 2 sides (a and b) and area of an oblique triangle. You must provide…

Q: Given: H = 52 ft, 80 h₁ = 47 ft, h₂= 50. 75 ft, discharge q under steady condition ft3/min, r = 10…

A: Unconfirmed aquifer with drawdown , radius information have been given and it has been asked to…

Q: Question 4 This question shows an application of multiple integrals in engineering and some…

A: Given a rectangular panel in which the hydrostatic force is acting. The panel has a depth of H and…

Q: 3- A cylindrical thin-walled pressure vessel was made by welding components together in a helical…

Concept explainers

Evaporation

This topic is majorly taught in various undergraduate and postgraduate degree courses of:

Question

100%

2. Given the following Ks= 10mg/l; q^=18mg/mg VSSa-d; Kd= .25d-1; Y= 0.7; Sᵒ=1,000mg/l; Q = 1000
m3/d; Xa=0. Determine the size of reactor required to achieve an effluent substrate concentration of 1
mg/l for
a. a system with no input biomass
b. a system with input biomass of Xo= 10 mg/l, 100 mg/l and 1000mg/l
c. a system with Xo = 100 mg/l and effluent s = 0.1, 1, 10, and 100 mg/l

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Data

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Trending now

This is a popular solution!

Step by step

Solved in 9 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4 An activated sludge system is to be used for secondary treatment of 10,000 m³/d of municipal wastewater. After primary clarification, the BOD is 150 mg/L, and it is desired to have not more than 5 mg/L of soluble BOD in the effluent. A completely mixed reactor is to be used, and pilot-plant analysis has established the following kinetic values: Y = 0.5 kg/kg, k, = 0.05 d-¹. Assuming an MLSS concentration of 3000 mg/L and an underflow concentration of 10,000 mg/L from the secondary clarifier (MLVSS=0.8MLSS) determine (1) the volume of the reactor, (2) the mass and volume of solids that must be wasted each day, and (3) the recycle ratio.
Environmental Engineering: Three (3) continuously stirred tank reactors are to be used in series. All the reactors have a similar volume. The influent flow has a concentration 100 mg/L of A and a flow rate of 200 l/min. The reaction is first order and the rate constant is 0.30 hr-1. Using the given information: a. Determine the mean residence time and volume of each reactor if the removal or conversion of A is 90%. b. What are the concentrations of A and the rate of conversion in each reactor?
Environmental Engineering: Water Treatment Please consider each of the following points: a. Determine the required residence time for each reactor of 3 equal volume CSTRs in series given a zero-order reaction with a reaction rate constant, k = -5 mg/L hr. The influent concentration is 125 mg/L and 95% conversion is required across the three-reactor system. What is the total reactor system residence time? b. Determine the required residence time for a single CSTR given the same conditions. c. Determine the required residence time for a PFR given the same conditions. d. Why are all three residence time the same?
An ASP operating at equilibrium has an organic loading rate of 2 kg/m³/d and has MLSS of 3000 ratio is mg/1 in the aeration tank. The d-1 (round off to two decimal places). Food F M Biomass,
1. A CM reactor receives influent containing 10 mg/L of tracer dye for 2 hours. The tracer addition is terminated but the flowrate of water is maintained. The volume of the reactor is 10 L and the flowrate is 2 L/hr. What is the concentration of tracer in the reactor 1 hr after the dye addition is terminated? The reactor had an initial concentration of tracer of 1 mg/L when the tracer addition commenced.
A wastewater flow with the following characteristics is to be treated in a completely mixed activated-sludge system. This system is operated at the sludge age of 10d and treats wastewater flowing at 18,000 m3/d. Average influent BOD is 200 mg/L and 92% BOD removal has been achieved. Yield is 0.4 kg biomass/kg BOD and decay coefficient is kd = 0.06 d1. The reactor is designed to operate at a biomass concentration of 2,500 mg/L and the biomass concentration in return sludge is 15,000 mg/L. The mass of solids wasted each day? () tonne/d (*No unit)
Three CSTRs are to be used in series. The second reactor has a volume twice that of the first and third reactors. The influent flow has a concentration of 150 mg/L of TOC, and the flowrate is 100 gal/min (380 l/min). The reaction is first order, the rate constant is 0.4/hr.a. Determine the mean residence time and volume of each reactor if theremoval or conversion of TOC is 90% (for the entire system as a whole).b. What is the concentration of TOC in each reactor? c. What is the overall efficiency of this treatment process?
Consider a wastewater treatment reactor where with an influent flow rate of 2,500 m3/day and where the biomass has the following kinetic characteristics: fs0 = 0.7, KS = 10 mg/l, k= 10 mg/mg VSS-day, b = 0.1/day, Y=0.50 g VSS/g substrate, fd=0.8, and Xa=1,500 mg VSS/l. If the reactor was designed with a safety factor of 30, what is its design fs value.
An activated-sludge system is to be used for secondary treatment of 15,000 m3/d of municipal wastewater. After primary clarification, the BOD is 130 mg/L, and it is desired to have not more than 5 mg/L of soluble BOD in the effluent. A completely mixed reactor is to be used, and pilot-plant analysis has established the following kinetic values: Y = 0.6 kg/kg, kd = 0.07 d-1. Assuming an MLSS concentration of 2,750 mg/L and an underflow concentration of 11,000 mg/L from the secondary clarifier, determine the followings. [Use θc (MCRT or SRT) = 10 day.] 5.1. The volume of the reactor. 5.2. The mass and volume of solids that must be wasted each day. 5.3. The recycle ratio. Hint: θc = VX/QwXu : MCRT (mean cell-residence time) [or SRT (solids retention time)]; average time microbes spend in reactor = ratio of total biomass in reactor to biomass wasted per given time; currently most commonly used design parameter F/Mv: inversely proportional to SRT; ≈U (cell's specific substrate…
You are considering available options to meet new effluent quality standards for a particular contamination being treated at your plant. Currently you are operating with two reactors connected in parallel as shown in Figure 1(a). One reactor is a plug flow reactor (PFR), the other is a completely stirred tank reactor (CSTR). The following information is available: Design flow, Q: 60 L/min Influent concentration, Co: 10 mg/L Order of reaction: 1st Order Decay constant, k: 0.25 min! Volume of PFR, Vp: 360 L Volume of CSTR, Vc: 2280 L Using the above information, determine: a. The residence time, t, in each reactor; b. The effluent concentration from the PFR; C. The effluent concentration from the CSTR. d. The resulting effluent quality with the two reactors in parallel. You want to investigate whether operating these reactors in series will allow the required effluent standard of 0.25 mg/L to be met. You are therefore proposing the new configuration for the reactors shown in Figure 1(b)…
Wastewater is treated with an activated sludge plug flow reactor, similar to one seen at the Norman Water Reclamation Facility. The BOD5 after primary treatment is 100mg/L and the effluent limit is 5 mg/L BOD5. Use 1.00 h-1 as the maximum specific growth rate constant and typical values for the other biokinetic constants. The biomass concentration in the reactor is 2,500 mg/L MLSS based on a recycle ratio of 1. Calculate the mean cell residence time, in hours for this system
2. Given: Process tank shown below Find: (1) total surface area and (2) volume -3 m +3 m- 6m 4 m