Solve the sub-part (A) only,only typing 2. A single phase full wave ac voltage controller supplies an RL load. The input supplyvoltage is 230V, RMS at 50Hz. The load has L= 10mH, R = 1052, the delay angle ofSCR 1 and 2 are equal, where al=a2=/3, B=197.4°Determine :a. Conduction angle of the thyristor.b. RMS output voltage.c. The input power factor.

2. A single phase full wave ac voltage controller supplies an RL load. The input supply voltage is 230V, RMS at 50Hz. The load has L= 10mH, R = 1002, the delay angle of SCR 1 and 2 are equal, where al=a2=n/3, B=197.4° Determine: a. Conduction angle of the thyristor. b. RMS output voltage. c. The input power factor.

2. A single phase full wave ac voltage controller supplies an RL load. The input supply voltage is 230V, RMS at 50Hz. The load has L= 10mH, R = 1002, the delay angle of SCR 1 and 2 are equal, where al=a2=n/3, B=197.4° Determine: a. Conduction angle of the thyristor. b. RMS output voltage. c. The input power factor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
1. Single phase half-wave converter has a purely resistive load of R and delay angle is a= n/2 determine: (a) Rectification efficiency (b) Form factor (c) Ripple factor.
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
A single phase full converter feeds power to RLE load with R=10 ohm, L=10 mH and E=50 V, the ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 600 ?
For a full-wave phase control circuit draw the output voltage and current waveforms when firing angle α = 38°. Consider the load to be inductive.
D. a Hall effect generator. 7. When power to a resistance load is controlled by full-wave SCRs with a 90° firing angle, what is the load power factor? A. 0.87 B. 1.0 C. 0.71 D. 0
Calculate the ripple factor in a full wave combiner circuit and the value of the output frequency, if you know that The value of 8 = Voc and rms (out-10V) and the input frequency is 60 Hz...
Why the frequency will double when we rectify an ac input to dc output at the ripple factor ?
C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. C2 (ii). A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 40 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3 cm and the peak to peak distance is 5.6 cm. Determine the following: The frequency is The magnitude of the sine voltage is The amplitude is The R.M.S voltage is
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system
For the CRO square voltage waveform is shown in Figure. The 'time/cm' switch is on 5 ms/cm and the 'volts/cm' switch is on 2 V/cm. Calculate (a) the periodic time, (b) the peak to peak voltage, (c) the maximum voltage, (d) the time taken to complete half cycle The periodic time The peak to peak voltage The maximum voltage The time taken to complete half cycle
A single phase full converter feeds power to RLE load with R= 10 2, L = 10 mH and E = 50 V, the %3D ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 60°?