2. A bending test is performed on a concrete prism sample with dimensions of 4x4x16 cm. When the distance between the supports is 10 cm, the maximum load value measured is 2256 N. Calculate the maximum bending load on this sample.

2. A bending test is performed on a concrete prism sample with dimensions of 4x4x16 cm. When the distance between the supports is 10 cm, the maximum load value measured is 2256 N. Calculate the maximum bending load on this sample.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 1,000 cc container was just filled with sand in its loosest possible state and then the container…

A: Given : Volume of container = 1000 cc Void ratio = 0.64 Specific gravity of solids = 2.65 To Find…

Q: Given the tangent distance equal to 224.87 meters and the angle of intersection equal to 48, what is…

Q: coefficient of volume compressibility

A: Given data. σ'0=175 kpae0=1.1σ'0+∆σ0'=300 kpae=0.9Thickness of clay= 25 mmDetermine the volume…

Q: On what cases are these following surveying curves used: simple curves, compound curves, reverse…

A: On what cases are these following surveying curves used: simple curves, compound curves, reverse…

Q: What is the distance required to stop an average passenger car when brakes are applied on a 2%…

Q: 5. Following observations were taken from two traverse stations by means of a tacheometer fined with…

Q: PROBLEM 5-6 Determine the support reaction forces at points A and B in the three hinged system given…

Q: 1 million people in Hong Kong using low-flush toilet and low-flow shower head. • 1 million leaky…

A: Answer In order to calcualte the savings we need to first determine reduction in waste water…

Q: Informed consent: O Can sometimes occur through the marketplace O is irrelevant when there is a…

A: Concept- Informed consent- When assent to an interaction or action is given after awareness of…

Q: The tank and the fuel have an initial total mass of 8 kg. After 31 minutes the mass scale shows a…

A: Answer Initial total mass = 8 kg final total mass = 7.47 kg time of flow = 31 minutes Calculations…

Q: A canal has a flowrate of 4.5 m³/sec and has medium size silts with an average grain size of 0.016…

Q: The beam is fixed at A and supported by a roller at B, and is under a uniform load of 0.5 kips/ft.…

A: Given: Plastic moment capacity, Mp = 200 kips-ft To find: The location of the plastic hinge from A…

Q: A Fer 19 kN C A 4m 2m 8M+ 8m For the truss shown, determine the reactions and ba forces produced by…

Q: *10-52. Determine the moment of inertia of the area about the x axis. 10-53. Determine the moment of…

Q: From the given truss, find the force of member AB, Load 1 = 30 kN, Load 2 = 60 kN Solve this using…

Q: If the radius of a circular curve is 92.42 feet, what is its degree of curvature (in degrees decimal

Q: Discuss in detail the function of cranes and hoists and list the different types

A: This question is related to the Building design and Construction from Civil Engineering. In this…

Q: How many planes of symmetry do the objects shown below have? Indicate your answer in the space…

A: Answer 5) Given T section drawing has only one plane of symmetry We know that planes of symmetry…

Q: For the structure shown in Figure P-916 is hinged to fixed supports at A and E. Compute the maximum…

A: Given : Cross sectional are = 200 mm2 To Find : The max, compressive stress developed in bar BDE ?

Q: A compressive load P = 100 kN is applied, as shown in Fig., at a point 70 mm to the left and 30 mm…

Q: 10-30. Determine the moment of inertia for the beam's cross-sectional area about the x axis. 10-31.…

Q: 6 kN/m 30 kN T ttt 3m (b) 20 KN |20|1=1

Q: Q5- Draw ILD for Ra, Rc,Rd,Rf, Vc-,Vc+, Vk and Mk. Hinge Hinge A 4 m B • 4 m C K 2 -10 m- D 9 4 m E…

Q: Which structural system is the most flexible and therefore has the highest R value? Special…

A: Q) Which Structural system is most flexible and therefore has highest R value Special reinforced…

Q: Water flows downward in a pipe at 30°. The pressure drop P₁ - P2 is partly due to gravity and partly…

A: Given- Height difference=50 cm, Water flow in the pipe with parameter shown in the figure. It is…

Q: Using the the following values, please calculate Mass of Soil (kg) (rounded to 3 decimal places):…

A: Mass of mold=4.714kg Mass of mol +soil=11.55kg To find mass of soil

Q: Draw

Q: For the solve for continous beaun shown, draw the ✓ and u diagram of Ely at the overhang. the value

A: To determine:Shear force and bending moment diagram

Q: Construction Management Question A newly built house is let out for rent of Rs.1,000 per month…

A: Given- Gross rent = Rs 1000 per month, Outgoings = 20% of the gross rent, Expected rate of return…

Q: Describe your recommended medium for connecting between buildings if it is known that the distance…

A: Given data- Two buildings, Distance between buildings D=500 m, To Find- The medium for connecting…

Q: QUESTION 2 Test Engineers found that 22% of steel frames fracture within 15 years. The average…

A: Given: 30 Psi is the average stress Required: What refers 30 Psi Note: No shear and bending…

Q: Two traffic signals are attached to the 36-ft support cable at equal intervals as shown. Determine…

A: Given, L = 36 ft w1 = 100 lb w2 = 215 lb

Q: Name the four main divisions of composite materials and cite the distinguishing feature of each.

A: Composite Materials: Composite materials are the materials that need specific technologies for their…

Q: 32 mm 60 mm bo 30 mm 24 mm 15 mm 180 mm 750 N 40 mm 500 N P 16 mm

A: To a cantilever beam, loading is given To determine normal and shear stress at points a, b, and c…

Q: In a hydraulic jump occurring in a rectangular channel of 3.0 m wide, carrying discharge of 7.8 cms,…

Q: 8. Determine the magnitude and direction of the resultant hydrostatic force the water exerts on the…

Q: From the given truss, find the force of member CH, Load 1 = 30 kN, Load 2 = 60 KN Solve this using…

Q: 10 kN A -20 kN/m 3 m 12 kN/m 3m B

Q: From the following cross-section notes, complete the table below. Use prismoidal method. Road bed…

Q: Aircraft Class 1 2 3 mix percentage | Aug. occupany "Time (min) 30 30 70 10 20 ५० Find the capacity…

Q: :A. If (PB-PA=97.4 kpa), Find (H). B. Write dynamic viscosity in MLT and FLT systems. Meriam red…

A: Given figure is inverted u tube manometer. Given differences in pressures are Pa-Pb = 97.4kpa From…

Q: A 20-foot ladder leans up against the side of a building so that the foot of the ladder is 10 feet…

Q: A 3 m long simply supported beam of uniformcross section is subjected to a uniformlydistributed load…

A: Given: Length of the beamL=3m Flexural rigidityEI=30×106 Nm2 Uniformly distributed loadw=20 kNm To…

Q: A leaf spring of semi-elliptical type has 11 plates each 9 cm wide and 1.5 cm thick. The length of…

Q: Q2/ Compute the Ground level of the points for the following readings: Points Station B.S I.S F.S…

Q: 2. Determine the design strength P of an A992 W18x50 connected by bolts on plates on both flanges as…

A: Answer From AISC Manual Table 1-1 W shape properties W 18 x 50 ( A = 14.7 in2 , bf = 7.50 in, tw =…

Q: Problem 01: Consider the beam loaded as shown and determine the following. Use Pn 10x Class number +…

Q: For major loss I got 9.81 as my answer not 40.77

A: Given, Pipe inner diameter, D = 2.5 cm = 0.025 m Pipe length, L = 20 m

Q: 3. The uniform girder AB has a mass of 8 Mg (Figure 3). Determine the internal axial, shear, and…

Q: 2. A saturated soil has the following characteristics: Initial Volume = 21 cc Final Volume = 16 cc…

A: Given data A saturated soil has the following characteristics: Initial Volume (V 1 )= 21cc Final…

Concept explainers

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.

Question

2. A bending test is performed on a concrete prism sample with dimensions of 4x4x16 cm. When the
distance between the supports is 10 cm, the maximum load value measured is 2256 N. Calculate the
maximum bending load on this sample.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Test for determination of shear strength

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A center point loading is used to test concrete for flexure. The sample is 150mm x 150mm and has a clear span of 600mm. The sample failed when the load applied is 100,000N. What is the flexure stress at failure in MPa?
A concrete specimen with b = d is supported at both ends 600mm apart. It is tested for flexure strength with load at midspan of 100kN and failed with a flexural stress of 52.083 MPa. What is the dimension b and d of the specimen in mm?
A cylindrical block of concrete is 300mm long and has a circular cross section of 100mm in diameter. It carries a total compressive load of 67KN and under this load contract 0.2mm. Estimate the compressive stress and strain .
In a pre-stressed concrete beam section shown in the figure, the net loss is 10% and the final pre- stressing force applied at X is 750 kN. The initial fiber stresses (in N/mm2) at the bottom of the beam were: d₁ d₁ b X મ ય ય ના તા b = 250mm d, = 200mm d₂ = 100mm Id₂
A 150mm diameter cylindrical concrete specimen was tested for splitting tensile strength.The splitting tensile stress at failure is 4.14 MPa, what is the applied force in kN?
A 150mm diameter cylindrical concrete specimen was tested for splitting tensile strength. The Sample failed when the applied force was 120 kN. What is the splitting tensile stress at failure in MPa? The sample length is 300mm
Tension controlled failure in reinforced concrete beams as per NSCP 2015 is when the tensile strain of rebars is 0.005 or larger. True False
A 150mm diameter cylindrical concrete specimen was tested for compressive strength. What would be the maximum applied force in kN when the stress at failure is 41.4 MPa?
A concrete cylinder sample has a diameter of 4 inches and a height of 6 inches. The maximum load carried by the sample after its failure is 275 KN. Determine the compressive strength of the sample in psi. (use 1lbf = 4.45 N, round-up your answer to the nearest whole number that is divisible by 5, no need for unit)
A 150mm x 300mm long cylindrical concrete specimen was tested for tensile strength. The sample failed when the applied force is 150,000N. What is the splitting tensile strength in MPa?
Strain profiles of a flexural reinforced concrete element section at yield and failure conditions are given in Figure 1. (a) Does this section satisfy the curvature ductility requirement of µ> 8. (b) Briefly indicate two possible design modifications by which the ductility of a reinforced concrete section can be improved. &= 0.002 Eu = 0.004 fy = 460 MPa Es = 200 GPa d Ey Es = 10ɛy Yield Failure Figure 1: Strain Profiles
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)