(2) At the moment shown, a particle of mass 1kg is traveling along the curved path. The radius of curvature of the path at the position of the particle is 300 m, and the particle is accelerating at a rate of 9 m/s². If the velocity of the particle at this position is 60 m/s, the resultant of the forces acting on the particle is: (a) 9 N (b) 12 N (c)) 15 N (d) 21 N

(2) At the moment shown, a particle of mass 1kg is traveling along the curved path. The radius of curvature of the path at the position of the particle is 300 m, and the particle is accelerating at a rate of 9 m/s². If the velocity of the particle at this position is 60 m/s, the resultant of the forces acting on the particle is: (a) 9 N (b) 12 N (c)) 15 N (d) 21 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two spheres A and B each have a mass of 400 g. The spheres are fixed to the horizontal rods as shown in (Figure 1) and their initial velocity is 2 m/s. The mass of the supporting frame is negligible and it is free to rotate. Neglect the size of the spheres. Figure -0.3 m S M 0.3 m B 1 of 1 Part A If a couple moment of M = 0.9 Nm is applied to the frame, determine the speed of the spheres in 3 s. Express your answer to three significant figures and include the appropriate units. V= Value Submit μA Provide Feedback Request Answer Units ?
Q1/ Determine the magnitude and direction angle(0) of force (F4) So that the particle shown in figure (1) is in equilibrium? F1=500 N F2=750 N F4 33° 30° 60° F3=1200 N
A homogeneous disk with a radius of 9 in. is welded to a rod AG with a length of 18 in. and of negligible weight that is connected by a clevis to a vertical shaft AB. The rod and disk can rotate freely about a horizontal axis AC, and shaft AB can rotate freely about a vertical axis. Initially, rod AG is horizontal (0o= 90°) and has no angular velocity about AC. Knowing that the smallest value of 0 in the ensuing motion is 30°, determine (a) the initial angular velocity of shaft AB (b) its maximum angular velocity.
The particle of mass m = 2.3 kg is attached to the end of the light rigid bar of length L = 0.83 m. The system is released from rest while in the horizontal position shown, at which the torsional spring is undeflected. The bar is then observed to rotate 45° before stopping momentarily, (a) Determine the value of the torsional spring constant kr. (b) For this value of kr, determine the speed vof the particle when e = 25°. kT Part 1 Position 1 is the horizontal orientation shown in the figure. Position 2 is the orientation when e- 45. Find the kinetic energy in positions 1 and 2. Answers: T1- kg m²/s2 T2- kg m²/s? Answers: (a) ky = i Nem/rad (b) m/s
A prismatic bar is fastened between two rigid walls A and Band subjected to loads as shown in figure. What will be the ratio of magnitude of reaction at A and B respectively? +13.6 kN Þ27.2 kN A C D В 100 mm 200 mm 300 mm
The uniform rod AB of mass 17 kg can rotate in a vertical x-y plane about an axis at G and is connected to a rectangular steel block of mass 35 kg to form a composite pendulum as shown in ! Note: The mass moment of inertia of a rod, mass m, length L, about its centroidal axis and perpendicular to the rod is l= ml?/12. The rectangular steel block has a mass moment of inertia of l= (1/12) m (a? + b?). 1.5 m G 2.5 m Rod Rectangular steel block 12m 3 m a) Draw the free body diagram and kinetic diagram of the pendulum. b) Formulate the equation of motion for small oscillations of the pendulum. c) Determine the natural period of oscillations.
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 155 N and the couple M = 573 Nm. M N m A 150 N 300 mm 250 mm PN 400 mm 90 N
In the given figure find the value of the reaction experience at hinge along C x-axis, if the weight of the bar is 500lb.
Beam AC is in equilibrium with loading 100 N at B shown in the figure when β = 45. Determine the unknown forces Ax and Ay at A in x and y direction and Rc perpendicular to the beam AC in y’ direction at C by using the equilibrium equations: ∑ ???= 0 ; ∑ ??y= 0; and ∑ ???= 0 where o is an arbitrary point. (you have three equations to solve three unknowns)
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA 120 mm 20 m INa = 30x106 mm What is the reaction at the support in kN?
A prismatic fixed-fixed beam, modelled with a total lumped-mass of 10 kg as a single degree of freedom (SDOF) system is shown in the figure. A B m E,I E,I 2 2 SDOF If the flexural stiffness of the beam is 4n2 kN/m, its natural frequency of vibration (in Hz, in integer) in the flexural mode will be,
Determine the moments of inertia about the centroidal axis of the figure shown