2) A 180° elbow forces the flow to make a U-turn and discharges it to the atmosphere at a mass flow rate of 40 kg/s. The diameter of the entire pipe is 10 cm. Calculate (a) the velocity of water in the pipe (b) the gauge pressure inside the pipe (c) the anchoring force needed to hold this pipe in place =180° OF

2) A 180° elbow forces the flow to make a U-turn and discharges it to the atmosphere at a mass flow rate of 40 kg/s. The diameter of the entire pipe is 10 cm. Calculate (a) the velocity of water in the pipe (b) the gauge pressure inside the pipe (c) the anchoring force needed to hold this pipe in place =180° OF

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
In the following figure the long tube is filled with water at 20°C. When valve A is closed, P₁-P₂ = 75kPa. When valve A is open and water flows at 500 m³/h, P₁ – P₂ = 160kPa What is the loss in lift due to friction between 1 and 2, for the condition in which the water flows? (p = 998 kg ,g = 9,812) m 73 1) Bomba R.SA (2)
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 m/s. The difference in elevation between the two water levels in the piezometers is 3 cm. The water temperature is 10oC. What is the velocity (m/s) at the minimum area?
A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of 50 m than the ground. The discharge at the end of the pipe is 220 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 35 N/cm². Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id....) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m) ,
A vertical pipe of 1 m diameter and 20 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.6 m of oil. The density of oil is 880 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) upward direction, (b) downward and also draw the neat sketch. i) Pressure at lower end when flow of oil is upward =________________ N/m2 ii) Pressure at lower end when flow of oil is downward =________________ N/m2
A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of 60 m than the ground. The discharge at the end of the pipe is 200 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm?. Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id...) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe
Air flows steadily between two sections in a long straight portion of 0.2 m inside diameter pipe as shown below. If the density of air at entrance and exist sections are p1 =1.21 kg/m3, p2 =1.47 kg/m3, calculate the average exist velocity V2 if the velocity at entrance is V1=152 m/s. D Section (1) Section (2) P1 = 100 Kpa (abs) P2 = 300 Kpa (abs)
Water fills a cylindrical tank to depth h . The tank hasdiameter D . The water fl ows out at average velocity V o from a hole in the bottom of area A o . Use the Reynoldstransport theorem to fi nd an expression for the instantaneousdepth change dh/dt .
Q-5 Water flows through a horizontal pipe that has a diameter of 4 cm at the entrance and 2 cm at the exit. The pressure drop across the pipe is 2.7 kPa. Calculate the speed of the water in the pipe, and Re number at section 1.
3. (a) A nozzle of inlet area A₁ and exit area A2 exhausts to atmosphere. A fluid of density p enters the nozzle with pressure p₁ (gauge) and velocity u₁. Show that the force trying to separate the nozzle from the pipe is given by 2 F = P₁A₁ - pA₁u₁² whether the nozzle is frictionless or not. A₁ A₂ -1)
In an industrial cooling process, water is circulated through a system. If water is pump from the first floor through a 6cm diameter pipe with a speed of 0.45 m/s under a pressure of 400torr, what will be the pressure on the nest floor 4m above into a pipe with diameter 2cm? Show your solution