1st:Using the formula t =determine theCaa/29coefficient of discharge.“A" of tankNote:1. "A" depends on the size of your bottle,2. "a" depends on the size of the hole you punched3. Let the initial head of water equal to 10 cm4. You can determine "t" through experiment5. Hence, the only unknown is the value of Cd.6. Repeat the process, try using head of water equalto 15 cm, then 20 cm.“a" of orifice7. Hence, you have 3 values of Cd.8. Tabulate and graph the results. Be creative.Referred: 1.5 L water bottle or alikeYou need to provide pictures for No.1 to No.3.Show your solution in No.5. (x3 due to trial 1, 2,and 3.2nd:Utilizing the same bottle, determine the averagevelocity of the fluid flowing through the water usingthe formula Q = CqA¿V¢ -"A" of tankNote:• Let Q = Volume / time. Use a beaker or measuringcup to determine the volume, then record the time“a" of orificeuntil water "runs" out. Be careful, volume refersonly to the amount of water above the orifice;water below the orifice won't flow out.Trials 1, 2, 3 = 100 ml, 500 ml, 1000 mlLet Cd = average Cd obtained from the previousexperiment.• At = area of orifice.• Hence, only unknown is Vt; but in this case we'llcall it average velocity because the formula Q =CaAtVt applies only if the liquid head is constant.Compare your obtained V-ave with V-theoretical(sq. rt. of 2gh). Share your thoughts and explain.• Show pictures and calculations.Include the procedure/steps using your own words.

Name: 1st:Using the formula t =determine theCaa/29coefficient of discharge.
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 1st:Using the formula t =determine theCaa/29coefficient of discharge.“A" of tankNote:1. "A" depends on the size of your bottle,2. "a" depends on the size of the hole you punched3. Let the initial head of water equal to 10 cm4. You can determine "t"

Since you have asked multiple questions, we will solve the first question for you. If you want any…

Engineering

Mechanical Engineering

1st: Using the formula t=24(/h3/h2) determine the "A" of tank Caa/2g coefficient of discharge. Note: 1. "A" depends on the size of your bottle, 2. "a" depends on the size of the hole you punched 3. Let the initial head of water equal to 10 cm 4. You can determine "t" through experiment 5. Hence, the only unknown is the value of Cd. 6. Repeat the process, try using head of water equal to 15 cm, then 20 cm. 7. Hence, you have 3 values of Cd. 8. Tabulate and graph the results. Be creative. "a" of orifice Referred: 1.5 L water bottle or alike You need to provide pictures for No.1 to No.3. Show your solution in No.5. (x3 due to trial 1, 2, and 3.

1st: Using the formula t=24(/h3/h2) determine the "A" of tank Caa/2g coefficient of discharge. Note: 1. "A" depends on the size of your bottle, 2. "a" depends on the size of the hole you punched 3. Let the initial head of water equal to 10 cm 4. You can determine "t" through experiment 5. Hence, the only unknown is the value of Cd. 6. Repeat the process, try using head of water equal to 15 cm, then 20 cm. 7. Hence, you have 3 values of Cd. 8. Tabulate and graph the results. Be creative. "a" of orifice Referred: 1.5 L water bottle or alike You need to provide pictures for No.1 to No.3. Show your solution in No.5. (x3 due to trial 1, 2, and 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Inlet and throat diameters of a horizontal venturimeter are 280 mm and 100 mm respectively. The liquid flowing through the venturimeter is water. Pressure intensity at inlet is 15 N/cm2, while pressure at throat is 50 kPa. Find flow rate of water in lit/min, assuming Cd is 0.7 and also draw the neat sketch. i) Actual flow rate = _______________________ lit/min.
3). in the figure below. Consider the acceleration due to gravity as g=32.2 ft/s², specific weight of water as yw-Pwg=62.4 lb/ft³ and gasoline as ygasoline=Pgasolineg=42.5 lb/ft³. What pressure, pi, is needed to produce a flowrate of 0.09 ft³/s from the tank shown Air Gasoline 2.0 ft Salt water 3.6 ft SG = 1.1 0.06-ft diameter -
... hm www 25mm diameter 2m 75mm diameter 1 water 200mm 600mm Mercury (SG = 13.6) %3D The head lost from point 1 to point 2 is 4m. If the specific gravity of mercury is 13.6, determine the following: a) The velocity at point 1 is Blank 1 m/s. b) The maximum height the water can reach "hm" if neglecting air friction is Blank 2 m Blank 1 Add your answer Blank 2 Add your answer 2.
2. The specific speed of a turbine is 85 rpm and running at 500 rpm. What is the maximum power, in HP, delivered by the generator if the head is 25 m and generator efficiency is 90 %. Copy the problem, then show Complete Solution/s (i.e. transformations, equivalent formula, etc).
A sealed tank filled with a fluid which is maintained at 0.35 bar gauge and 20 0C. The fluid discharges to the atmosphere (1.013bar) through a small opening at the side of the tank (z1 = z2 ). a) Calculate the velocity of fluid leaving the tank; assume the flow to be compressible and the process to be frictionless adiabatic.b) Calculate the velocity of fluid leaving the tank if the flow is incompressible and the process to be frictionless.c) Compare the calculated velocities and comment on the result. Take for fluid,α=1.0P=kρɤ ɤ =1.4R=287 J/kg.KMach number<0.3, incompressible flow. (Fluid Mechanics Question) (Please solve step by step)
... P1 = 50 KPa P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifice %3D has a diameter of 100mm and is under the surface of oil, 4m from the surface on the left and 1.6m from the surface on the right. The surface at the left is under 50KPA of pressure and the surface at the right side is under 1OKPA of pressure. Determine the actual discharge in the orifice if C = 0.92 112.03 L/s B 87.63 L/s 95.25 L/s 103.07 L/s No Answer among the choices
Q2: Water is flowing through a horizontal venture meter. The inlet diameter is 250 mm, while the throat diameter is 50 mm; the inlet pressure is 14.235 N/em while the vacuum pressure head at the throat is 38.5 cm of mercury, suppose that 5.5% of the differential head is lost between the inlet and throat. Find. i) ii) The value of discharge coefficient for the venture meter Ca? The discharge rate of flow?
pls ans asap Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the diameter of the pipe, in millimeter (mm), that was used is
1. Solve the following and draw the figures Í. A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward direction. A differential mercury manometer connected to the inlet and throat gives a reading of 30 cm. Find the [Ans. 154.02 lit/s] ii. If in the problem 13, instead of water, oil of sp. gr. 0.8 is flowing through the venturimeter, determine the [Ans. 173.56 lit/s] III. The water is flowing through a pipe of diameter 30 cm. The pipe is inclined and a venturimeter is inserted in the pipe. The diameter of venturimeter at throat is 15 cm. The difference of pressure between the inlet and throat of the venturimeter is measured by a liquid of sp. gr. 0.8 in an inverted U-tube which gives a reading of 40 cm. The loss of head between the inlet and throat is 0.3 times the kinetic head of the pipe. [Ans. 22.64 lit./s] discharge. Take Ca = 0.98. rate of flow of oil in litres/s. Find the discharge.
Please solve complete in one hour water flows out of a pressurized tank through a smooth pipe with Q = 50 m³ / h. In this problem we will find out how big the pressure p1 must be to produce this volume flow? a) What assumptions and simplifications must be made? b) Find the pressure p1. c) Find the same pressure, but using Bernoulli's equation. Comment, what is the difference?
After graduation, you work for a pump manufacturing company. One of your company’s best-selling products is a water pump, which we shall call pump A. Its impeller diameter is DA = 6.0 cm, and its performance data when operating at n. A = 1725 rpm (?A = 180.6 rad/s) are shown in Table.The marketing research department is recommending that the company design a new product, namely, a larger pump (which we shall call pump B) that will be used to pump liquid refrigerant R-134a at room temperature. The pump is to be designed such that its best efficiency point occurs as close as possible to a volume flow rate of V. B = 2400 cm3 /s and at a net head of HB = 450 cm (of R-134a). The chief engineer (your boss) tells you to perform some preliminary analyses using pump scaling laws to determine if a geometrically scaled-up pump could be designed and built to meet the given requirements. (a) Plot the performance curves of pump A in both dimensional and dimensionless form, and identify the best…
Q No. 5: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no losses. Note : Please Solve as Per Question's Statement. Need a Neat and Clear Solution.See Attached Picture For Detail .