169 g of solid water (i.e. ice), at -17 °C, is placed into a sealed, insulated container with a volume of 0.29 m^3. A 1457 W heater is used to heat and change the phase of the sample until it is a gaseous water (i.e. steam). The heater runs for 433 s. What is the pressure, in kPa, of the gaseous water in the container at the end of the heating process?

169 g of solid water (i.e. ice), at -17 °C, is placed into a sealed, insulated container with a volume of 0.29 m^3. A 1457 W heater is used to heat and change the phase of the sample until it is a gaseous water (i.e. steam). The heater runs for 433 s. What is the pressure, in kPa, of the gaseous water in the container at the end of the heating process?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 300 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.7 m'/kg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
In the air conditioning process in the humidifier, air at a dry bulb temperature of 30 degrees C and RH of 10% increases its RH to 50%. Determine the amount of moisture added in the humidifier per kg of dry air: ....
A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 mkg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work đuring the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
B2. The heat energy of 1605 kJ is supplied to saltwater in the steam generator to heat from 25°C to 104°C for the generation of water vapor, Take the density & specific heat of the solution as 1028 kg/m³ & 3 J/kg°K respectively. Determine the quantity of saltwater in the steam generator. I Solution: i) Change in Temperature (in K) ii) Mass of the saltwater (in kg) iii) Quantity (Volume) of salt water (in m³)
What is the volume of 0.5 kg of superheated steam at 15 bar and 400oC ?
What is the phase and pressure of water at 120°C with specific volume 3.0 m3/kg?
Find the amount of ice (gram) at - 5.00 Celsius that is needed to cool a mixture of 0.200 kg substance A and 0.300 kg substance B from 18.0 Celsius to 12.0 Celsius
Water boils at 100°C at atmospheric pressure, that is, at sea level (To=15ºC). The boiling point is defined as the temperature at which the vapor pressure of water is equal to the atmospheric pressure. This has consequences for cooking in places such as Atok where it takes quite a bit longer to make a hard-boiled egg than it would in Baguio City. If the albumen in an egg needs to reach 75°C for the protein to coagulate, at what height would it be impossible to hard boil an egg?
Required information m³/kg. A 1.76-m³ rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. The properties of steam at 220°C are given as follows: vf= 0.001190 m³/kg and vg = 0.08609 m NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Steam Vm³ 220°C Determine the pressure of the steam. The pressure of the steam is 2319.6 kPa.
1 kg of Oxygen has initial volume of 2 x 10° cm³ is heated at Isobaric process from 298 K to 200°C. Calculate (i) ratio of specific heats (i) heat transfer in 'kl' (ii) work transfer in 'kJ'(V) change in internal energy in 'kl' (V) volume after heating (vi) pressure before heating in "bar'. Gas (kJlkg K) (kJ/kg K) Air 1.005 0.718 Oxygen Nitrogen Hydrogen 0.920 0.660 1.046 0.754 14.40 10.40 Carbon monoxide 1.046 0.754
An ideal gas is enclosed in a constant volume container at a pressure of 0.7 atm and an initial temperature of 100 degree centigrade. The pressure is then decreased to 0.512 atm with a temperature of 37degree centigrade. If the pressure is then decreased again to 0.34atm. What is the final temperature.