14 A cylindrical vessel closed at the top and bottom is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its vertical axis, find the pressure head at the bottom of the vessel at the center point and at the edee.

14 A cylindrical vessel closed at the top and bottom is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its vertical axis, find the pressure head at the bottom of the vessel at the center point and at the edee.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two pressurized prismatic tanks B and P are connected at their sides by an orifice having 100 mm radius. Tank B contains water at a depth of 3.2 m above the orifice and a pressure of 50 kPa on the water surface. Tank B also a depth of 2.15 m above the orifice The contains water at of 17 kPa the water surface. and a pressure on coefficient of discharge is 0.86 and the coefficient of velocity is 0.92. Compute the following: a. Compute the flow through the pipe. b. Compute the head lost in the orifice. c. Compute the power lost.
Homework 14 |A cylindrical vessel closed at the top and bo om is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its ver cal axis, nd the pressure head at the bo om of the vessel at the center point and at the edge.
A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another gage at elevation 7 m reads 140 kPa. Compute the specific weight of the liquid. 100 kPa - El. 12 Sm 140 kPa El. 7
A closed cylindrical tank having a radius of 0.60m and a height of 4m is full of water under a pressure of 196.2 kPa. If the vessel is rotated at 200 rpm: (a) Compute the total pressure on the side wall and (b) compute the total pressure against the top. Imaginaryy=8.04 water surface Closed- h=2d 4m Pawh -1.2- -1.2- 2.
Homework 14 A cylindrical vessel closed at the top and bottom is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its vertical axis, find the pressure head at the bottom of the vessel at the center point and at the edge.
A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another gage at elevation 7 m reads 140 kPa. Compute the specific gravity of the liquid. L00 kPa - EL. 12 Sm 140 kPa - El. 7
The fluid in the tank is water. Flow is steady state, incompressible and nonviscid. It is known that the pressure at point (1) is 41.5 kPa(gage). Determine the height x of the tank? 5-m 0.02-m diameter 0.03-m diameter | (1) 0.01-m diameter
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
height of water at that point. 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. E the pressure intensity : () at the interface of the two liquids, and (i) at the bottom of the tank. (Ans. () 1.57 N/em', (i) 3.04 Niem 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively. A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when : (a) the pistons an at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jacks [Ans. (a) 1500 N, (b) 15205 N] kg given as 1000 - m 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/em? (gauge), 12.066 N/em (abs.)) atmospheric pressure as 10.1043 Nicm. 9. A simple manometer is used to measure the pressure of oil (sp. gr. = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere…
Determine the available NPSH for the system shown in Fig. 13.38 (b). The fluid is water at 80°C and the atmospheric pressure is 101.8 kPa. The water level in the tank is 2.0 m below the pump inlet. The vertical leg of the suction line is a DN 80 Schedule 40 steel pipe, whereas the horizontal leg is a DN 50 Schedule 40 pipe, 1.5 m long. The elbow is of the long-radius type. Neglect the loss in the reducer. The foot valve and strainer are of the hingeddisk type. The flow rate is 300 L/min.
Q2: A tank of water empties by gravity through a siphon. The difference in levels is 3 m and the highest point of the siphon is 2m above the top surface level and the length of pipe from inlet to the highest point is 3.5 m.The pipe has abore of 40 mm and length 12m. The friction coefficient for the pipe is 0.009 The inlet loss coefficient K is 0.9. Determine total of Resistance. (0) Fig.(2)
2.6 An open tank contains water upto a de pth of 2 m and above it an oil of sp. gr. 0.9 for a depih of 1 m. Find the pressure intensity (i) at the interface of the two liquids, and (ii) at the bottom of the tank.