11 Which of the following statements is true? A) The internal resistance of an ammeter is very high. B) The internal resistance of a voltmeter is very low. C) An ammeter measures current and should not be connected in parallel. D) A voltmeter measures voltage and should be connected in series. E) None of the above. 12 Given an analog signal with highest frequency of 30 KHz, what is the minimum sampling rate needed in order to make the signal can be reconstructed perfectly? A) 15 KHz B) 30 KHz C) 40 KHz D) 50 KHz E) 60 KHz answer in typing format please all subpart is compulsory please 13 What is the equivalent resistance between terminals a and b? A) 28 ohms B) 11.4 ohms C) 12 ohms D) 15 ohms E) 10 ohms 1292 www 20 Ω 60 Ω 30 52 4052 oa ob please answer all questions, much appreciated. Thank you.

11 Which of the following statements is true? A) The internal resistance of an ammeter is very high. B) The internal resistance of a voltmeter is very low. C) An ammeter measures current and should not be connected in parallel. D) A voltmeter measures voltage and should be connected in series. E) None of the above. 12 Given an analog signal with highest frequency of 30 KHz, what is the minimum sampling rate needed in order to make the signal can be reconstructed perfectly? A) 15 KHz B) 30 KHz C) 40 KHz D) 50 KHz E) 60 KHz answer in typing format please all subpart is compulsory please 13 What is the equivalent resistance between terminals a and b? A) 28 ohms B) 11.4 ohms C) 12 ohms D) 15 ohms E) 10 ohms 1292 www 20 Ω 60 Ω 30 52 4052 oa ob please answer all questions, much appreciated. Thank you.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

16 digital electronics Which of the following is true about the noise margin according to the figures given in the figure? b) the question is wrong d) none
Shown below is a section from the datasheet of 74LS32, a quad 2-input OR chip. What is the noise margin high (in V) of this chip? Limits Symbol Parameter Min Typ Max Unit VIH Input HIGH Voltage 2.0 V VIL Input LOW Voltage V 0.8 VIK Input Clamp Diode Voltage -0.65 -1.5 V V VOH Output HIGH Voltage 3.5 V V VOL Output LOW Voltage 0.35 0.5 V 20 μA IH Input HIGH Current 0.1 mA IIL Input LOW Current -0.4 mA los Short Circuit Current (Note 1) -100 mA Power Supply Current Icc 6.2 Total, Output HIGH mA Total, Output LOW 9.8 74 74 74 2.7 -20
The term that refers to infinite no of values in the range is a. Peak b. Analog Signal c. Digital Signal d. None of the above
Consider the following figure. Represent the discrete samples into their corresponding hex values. Draw the analog signal. Image below:
The sensitivity of a PMMC instrument is 10k /V. If this instrument is used in a rectifier type voltmeter with half wave rectification, the sensitivity will be:
Digital signal process
B- An rate. analog signal having single frequency as 3 kHz is sampled with 5 kHz S Describe its frequency spectrum. What will be the output if the sampled signals a passed through a low-pass filter having cutoff frequency at 2.5 kHz? signal. are sent in the analog
QUESTION 1 Find out the rounded integer output (in decimal format) of a10 bit A/D converter for the following two cases? Assume that the input to ADC in both cases is 500mV. Also, assume that the ADC uses a 15V supply voltage. The converter input range is 0 to 10V. Case 1: Reference voltage: 10V. Case 2: Reference Voltage: 5V. A 26 and 51 B 52 and 103 C 104 and 206 D 26 and 206 In Question 1, If a choice is given, which reference voltage you would pick? A. 5V B. 10V C. 20V D. All choices give same results In Question 1, What is the ADC output value (in decimal format) for the input of 7V for the case of reference voltage = 5V? Answer: 1023 Answers are highlighted. Work Step-by-Step solution to get the answer.
In a digital voltmeter, the oscillator frequency is 400 kHz. A ramp voltage to be measured by this voltmeter falls from 8 V to 0 V in 20 ms. The number of pulses counted by the counter is?
Draw the outputs of the circuits to scale according to the input signal.
Assuming that a certain ASM chart has 5 states, the size of each multiplexer required to implement this circuit using the multiplexer design approach should be: Select one: O a. Four to one. O b. Eight to one. O . None of the given. O d. Two to one.
To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. a- Identify the assigned voltages to each of the bins. b- Determine the voltage that will be assigned to a measurement reading -3.25 V. Calculate the percentage ADC error. c- Determine the voltage that will be assigned to a measurement reading 4.11 V. Calculate the percentage ADC error.