10 m3 of free air is compressed to 8 bar gauge, every minute. What will be the air volumetric flowrate at the compressor exit if air is assumed an ideal gas ? please choose correct option a. 1.11 m3/min b. 2πdt m3/sec c. 1.27 litre/sec d. 1.11 m3/hour e. 2.2 litre/sec

10 m3 of free air is compressed to 8 bar gauge, every minute. What will be the air volumetric flowrate at the compressor exit if air is assumed an ideal gas ? please choose correct option a. 1.11 m3/min b. 2πdt m3/sec c. 1.27 litre/sec d. 1.11 m3/hour e. 2.2 litre/sec

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter3: Basic Theories And Math

Section: Chapter Questions

Problem 9RQ: Describe the effect of pressure on an enclosed volume of a gas.

See similar textbooks

Related questions

Q: As shown in the figure, air with a volumetric flow rate of 17,000 ft/min enters an air-handling unit…

Q: As shown in the figure, air with a volumetric flow rate of 14,000 ft³/min enters an air-handling…

Q: 1. A complete breakdown of airflow through a compressor is known as: Compressor surge. Compressor…

A: A complete breakdown of airflow through a compressor is known as Compressor surge.

Q: ation of Mass Questions 76-80 are based air entering a compressor operating at steady state with a…

A: Dear student, According to the guidelines I am allowed to answer only first three…

Q: As shown in the figure, air with a volumetric flow rate of 17,000 ft°/min enters an air-handling…

A: Given,…

Q: Figurel: Layout of industrial gas compressor with an air receiver The given information is…

Q: ..Equation for Law of conservation of mass and energy for a nozzle

A: Law of conservation of mass (For nozzle) The mass is conserved during the process, the mass of fluid…

Q: As shown in the figure, air with a volumetric flow rate of 14,000 ft/min enters an air-handling unit…

A: The standard value of the density of air at 80oF and 1 atm is 0.0735 lb/ft3. Write the given data.…

Q: As shown in the figure, air with a volumetric flow rate of 14,000 ft3/min enters an air-handling…

A: Determine the specific volume.

Q: As shown in the figure, air with a volumetric flow rate of 15,000 ft/min enters an air-handling unit…

A: ⇒given data;⇒volumetric flow rate of air or discharge from air handling(v1 or…

Q: 11. Forty gal/min of a hydrocarbon fuel having a specific gravity of 0.91 flows into a tank truck…

A: Density of pure water, ρ=8.34 lb/gal,so the density of the fluid=specific gravity×density of pure…

Q: A receiver must supply air to a pneumatic system consuming 30 scfm for 15 min between 140 psi and…

A: As per given question We have to determine the size is required if the compressor is running and…

Q: Question 3 A four-cylinder of 1.6 liters S.I engine (S4PH with BSFC = 0.5 lb/HP- hour) has the…

A: Given dataN=4BSFC=0.5Injector size =240 cc/minQ'=240 cc/minP'=43.5 psiP=50 psi ***As per company…

Q: Methanol (SG=0.792) is contained in a large tank under a pressure of 350000 Pa absolute. When a…

Q: ne specific gravity of a liquid fuel at 15.6°C is 0.88. What is its ensity at 32°C?

Q: QUESTION 18 Describe the T-s diagrams accordingly by filling it the blanks accordingly. Use the sets…

A: To match: The image with appropriate cycle. Explanation: Carnot vapor cycle: In Carnot vapor cycle…

Q: Pressure drop and heat transfer in suction line Decrease compression ratio & discharge temperature…

A: Pressure drop and heat transfer in suction line increases compression ratio and discharge…

Q: The control volume means changing the volume of a fluid at constant pressure Ture False O

A: Given Statement :- The control volume means changing the volume of a fluid at constant pressure.…

Q: m3 /second is SI the unit of a. Pressure b. Discharge c. Velocity

A: A discharge is a measurable quantity of any fluid flow over unit time. Mathematically, discharge is…

Q: QUESTION 17 At the exhaust of a turboject engine the nozzle is operating steadily and heat loss is…

A: To find: The velocity of the fluid at the exit of the nozzle. Given: The specific enthalpy at the…

Q: he figure below provides steady-state data for water vapor flowing through a piping configuration…

A: GivenV1=35m/sT1=200°C

Q: The dry bulb of a wet/dry thermometer reads 120°F. What is the relative humidity if the wet bulb…

Q: air in an internal combustion engine has 227 degrees Celcius, 1000 kPa, with a volume of 0.1 cubic…

A: Hi, you have submitted multiple questions and it is not specified in which problem you need help.…

Q: Show solution An air compressor has a suction volume of 0.3m^3/s at 28℃ & 1 atm and discharges to…

Q: 7. An automobile tire contains 3730 cu in. of air at 32 psig and 80°F. (a) What mass of air is in…

Q: As shown in the figure, air with a volumetric flow rate of 15,000 ft³/min enters an air-handling…

Q: Which statement is correct for a compressed air tank? a) As the temperature decreases, the pressure…

A: if the temperature go below boiling point of air

Q: A fan operating at a standard air condition registered a total static head of 230 mm of water gage.…

A: Given Data Total static head, hs=230 mm Static efficiency, ηs=0.65 Fan efficiency, ηf=0.8 Velocity…

Q: a rocket engine has a Cf =1.6, Pc=1000psia, throat area of 100 in^2, Isp=400s, and MR=3, what is the…

A: Thrust F=CFPcAt Also F =mpgIsp

Q: As shown in the figure, air with a volumetric flow rate of 16,000 ft°/min enters an air-handling…

Q: A car generator turns ar 301 rpm when the engine is idling ,

A: Given Data The angular speed of the car generator is:ω=301 rpm The number of turns is:N=296 turns…

Q: On the Mindray A5/A3, during the leak test the pressure indicated by the airway pressure gauge fails…

A: Given that the failure description is: the Mindray A5/A3, during the leak test the pressure…

Q: A supply line carries a two-phase liquid–vapour mixture of steam at 450 psi. A small fraction of the…

Q: Assuming the clearance is negligible for a single stage compressor with the following data.…

A: To obtain the temperature of the gas after the isentropic compression, the given relation must be…

Q: Question 2 A two stage, single acting, reciprocating compressor takes in air at a rate of 2 m/s at a…

Q: A compressor increases the of a gas by its Select one: O a. pressure, increasing, volume O b.…

Q: shown in the figure, air with a volumetric flow rate of 17,000 ft3/min enters an air-handling unit…

A: Duct is the passage through which air is passed to the required applications. The air handled under…

Q: As shown in the figure, air with a volumetric flow rate of 17,000 ft%/min enters an air-handling…

Q: As shown in the figure, air with a volumetric flow rate of 17,000 ft°/min enters an air-handling…

Q: velocity at the top of the hill?

A: to find final velocity.

Q: An unknown ideal gas at 53 deg F and 3.3 in Hg (gauge) is flowing through an irregular duct. To…

A: The above-given problem is related to the mixture of gases. So to obtain the solution to the above…

Q: b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the…

Q: As shown in the figure, air with a volumetric flow rate of 17,000 ft3/min enters an air-handling…

Q: question 1) 1. Describe how the mean effective pressure for reciprocating engines is defined and…

A: Mean effective pressure: It is a useful relative engine performance measurement quantity which is…

Q: As shown in the figure, air with a volumetric flow rate of 14,000 ft/min enters an air-handling unit…

A: Given: The system is shown below:

Q: Assuming the clearance is negligible for a single stage compressor with the following data.…

Question

10 m3 of free air is compressed to 8 bar gauge, every minute. What will be the air volumetric flowrate at the compressor exit if air is assumed an ideal gas ?

please choose correct option

a.
1.11 m3/min

b.
2πdt m3/sec

c.
1.27 litre/sec

d.
1.11 m3/hour

e.
2.2 litre/sec

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

b) The bore diameter of each cylinder in a sir-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing, the engine runs at 1450 revolutions per minute (pm) with a pressure-volume indicator diagram showing a mean net area of 2 90 cm' and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kNmper cm Calculate the mean effective pressure (mep) and the indicated power in klowatts (aW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal places. c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. the maximum allowable stress for this hollow rod is 325 KNimm, calculate the minimum thickness of the rod. Give your answer in millimetres (mm) and to 2 decimal places.
A large mining company was provided with a 3000 cm3 of compressed air tank. Air pressure in the tank drops from 700 KPa to 180 KPa while the temperature remains unchanged at 28 deg Celcius. What percentage has the mass of air in the tank been reduced? a.72% b.78% c.74% d.76% show your complete solution
Describe the effect of pressure on an enclosed volume of a gas.
10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler pressure of 2 bar gauge and polytropic index of 1.3, what will be the flowrate at the exit of the intercooler ?Please choose correct option.a.4.295 m3/minb.312 litre/sec.c.3333 litre/mind.1172 litre/min.e.981 m3/min
27. A closed vessel contains air at a pressure of l130 kN/m´ gauge and temperature of 30°C. The air is heated at constant volume to 60°C with the atmospheric pressure of 759 mmHg. What is the final gauge pressure?
5/ Which physical quantity can be measured with RTD? a. Flow b. Temperature c. Pressure d. Level
Determine the output pressure of a compressor operating with the following data: a. Actual power required to drive the compressor is 20 kW. b. Overall efficiency of the compressor is 75%. c. Compressor delivers four standard m3/min. d. Compressor inlet pressure is 100 kPa abs.
Provide complete solution and detailed diagram. How much heat, KJ must be transferred to 20 kg of air to increase the temperature from 20oC to 280oC if pressure is remained constant ? A. 2500 B. 2050 C. 5200 D. 5500
1. If 1 gallon of oil = 1.4 therm, how many gallons have been wasted by heat loss in Feb? (1 therm = 100,000 BTU)_____________________________________________________________________________________2. If $1.30 per therm, how much did you waste from house heat loss in Feb?
21. The following are the results of tests conducted on a centrifugal pump. Negative pressure head in suction pipe close to pump =22 cms of mercur y Pressure he id in delivery pipe close to pump=1'50 kg/cm2 Difference of level between the two gauges 0 50 metres SHP of the electric motor Discharge of the pump * Dianeter of the suction pipe Diameter of the delivery pipe Calculate the overall efficieney of the pump. -32 hp -010 cumeo %3D =20 cma 18 cms (78 17%)
The bulk modulus of fluid (K) equals: Select one: O a. PV/AV O b. VAV/AP O c. None of all O d. PAV/V
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 1, P1(gage)=______ A. Patm B. 0 C. 101.325 kPa D. It can not be determined.