10-23 Problem 10-23 Clamping fixture. A holding fixture for a workpiece 37.5 mm thick at the clamp locations is being designed. The detail of one of the clamps is shown in the figure. A spring is required to drive the clamp upward when removing the workpiece with a starting force of 45 N. The clamp screw has an M10 X 1.25 thread. Allow a diametral clearance of 1.25 mm between it and the uncompressed spring. It is further specified that the free length of the spring should be Lo ≤ 48 mm, the solid height L, 31.5 mm, and the safety factor when closed solid should be n, 1.2. Starting with d = 2 mm, design a suitable helical coil compression spring for this fixture. For A227 HD steel, wire diameters are available in 0.2-mm increments between 0.2 to 3.2 mm. Clamp screw Spherical washer Slot Workpiece Clamp Groove Pin

10-23 Problem 10-23 Clamping fixture. A holding fixture for a workpiece 37.5 mm thick at the clamp locations is being designed. The detail of one of the clamps is shown in the figure. A spring is required to drive the clamp upward when removing the workpiece with a starting force of 45 N. The clamp screw has an M10 X 1.25 thread. Allow a diametral clearance of 1.25 mm between it and the uncompressed spring. It is further specified that the free length of the spring should be Lo ≤ 48 mm, the solid height L, 31.5 mm, and the safety factor when closed solid should be n, 1.2. Starting with d = 2 mm, design a suitable helical coil compression spring for this fixture. For A227 HD steel, wire diameters are available in 0.2-mm increments between 0.2 to 3.2 mm. Clamp screw Spherical washer Slot Workpiece Clamp Groove Pin

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.2P

See similar textbooks

Similar questions

A holding fixture for a workpiece 37.5 mm thick at the clamp locations is being designed. The detail of one of the clamps is shown in the figure. A spring is required to drive the clamp upward when removing the workpiece with a starting force of 45 N. The clamp screw has an M10x1.25 thread. Allow a diametral clearance of 1.25 mm between it and the uncompressed spring. It is further specified that the free length of the spring should be Lo ≤ 48 mm, the solid height L, S 31.5 mm, and the safety factor when closed solid should be n, 21.2. Starting with d=2 mm, design a suitable helical coil compression spring for this fixture. For A227 HD steel, wire diameters are available in 0.2-mm increments between 0.2 to 3.2 mm. Spherical washer Slot Workpiece - Clamp screw AAAAAA Clamp Groove Pin
L21. Figure P4-21 shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is to be 500 lb, specify a suitable diameter for the steel pin if it is to be made from SAE 1040 WQT 900. 4-21
A screw jack mechanism is shown in the figure below (not drawn to scale). A belt drives a sheave that rotates the nut. The screw is a single-thread,1 1/2-4 ACME screw. Notice that a pin is used in a groove to prevent the screw from rotating. The sheave has a pitch diameter of 14 inches. The belt is driven by an electric motor (not shown) with a sheave pitch diameter of 2.8 inches at 1650 rpm. Determine the lifting speed of the jack. Determine the belt speed. Find the lifting speed (s) of the jack (in/min): Find the belt speed vb (ft/min):
Information about the clamp assembly in the figure is given below. Thread diameter 12 mm, root diameter 10.16 mm, pitch 1.5 mm, screw profile angle 2α=60, friction surface of table A diameter 10 mm, friction between plate A-screw end surface coefficient 0.15 and screw-nut friction coefficient 0.15 is given. If a hand force of 200N is applied to the vise arm, if applied, a) How much force is applied to the clamped part. b) Calculate the efficiency of the vise.
A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in acyclical fashion as the mechanism runs. It has been decided to use AISI 1040 cold-drawn steel.Complete the design of the link, specifying a suitable cross-sectional shape and dimensions.5. Specify the required length of no. 60 chain to mount on sprockets having 15 and 50 teeth with acenter distance of no more than 36 in.
MM Diameter = ? Pin Anvil FIGURE P4-21 Impact hammer for Problem 4-21, 4-21. Figure P4-21 shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is to be 500 lb, specify a suitable diameter for the steel pin if it is to be made from SAE 1040 WQT 900.
The width of the belt used if its thickness is 6 mm. Ans. 261 mm 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt speed of 25 m/s. The belt has a mass of 2 kg/m of the belt length. The belt is used in a crossed configuration to connect a 300 mm diameter driving pulley to a 900 mm diameter driven pulley at a shaft spacing of 6 m. A. Calculate the belt length and the angles of wrap. Ans. 13.95 m, 3.34 rad or 191.4° B. Compute the belt tensions based on a coefficient of friction of 0.33. Ans. 1.76 KN, 1.96 KN
The machine is designed to be powered by a 100 HP electric motor at a speed of 1500 rpm, with standard D-120 V-belts. The pitch diameter of the smaller sheave is 101.6 mm and the bigger sheave is 406.4 mm. Service factor is 1.25. Use length of D-120 V-belt equal to 123.3 inches. Determine the center distance between sheaves in mm; the arc of contact in deg; and the design in HP.
PROBLEM: 7 Calculate the dimensions of helical spring for a spring loaded safety valve from the following data : Valve Diameter = 45 mm; operating pressure = 0.6 N/mm2 Maximum pressure when the valve blows off freely = 0.99 N/mm2 ;valve lift when pressure rises from 0.6 to 0.99 N/mm2 = 5.5 mm ;Maximum permissible stress = 555 N/mm2 ; spring index ,C = 9; Modulus of rigidity =0.85x 105 N/mm2. Assume the spring coil is squared and ground.
The figure shows a schematic drawing of a vehicular jack that is to be designed to support a maximum mass of 300 kg based on the use of a design factor na = 3.50. The opposite-handed threads on the two ends of the screw are cut to allow the link angle 0 to vary from 15 to 70°. The links are to be machined from AISI 1010 hot-rolled steel bars. Each of the four links is to consist of two bars, one on each side of the central bearings. The bars are to be 350 mm long and have a bar width of w = 30 mm. The pinned ends are to be designed to secure an end-condition constant of at least C = 1.4 for out-of-plane buckling. Find a suitable preferred thickness and the resulting factor of safety for this thickness. W 華 w
Q4-A square threaded screw is required to work against an axial force of 6000N and has following dimensions. Major dia. d = 32 mm; pitch p = 4 mm with single start, u = 0.08. Axial force rotates with the screw. Calculate the torque required when screw moves opposite the direction of the load
For the frame shown in Fig. 6-24a, draw the free-body diagrams of (a) the entire frame including the pulleys and cords, (b) the frame without the pulleys and cords, and (c) each of the pulleys. 3E Fx=0 +9 E fy=o 1. FIMD RXAS AT A$D Fing FoRLE componeAB 2. Ge Pits oF POLLEYS EM=0 Cx C By E Ay T. Ay AauLE OF RESOUTAT AT B, C &A 75 lb SKETCH RESULTALT (a) Fueo Manat AT BASE ア(y 7516 OF CULUneCE radius of the pulley at B linch Yadius of the Pulley at c a7s inch 75 lbs 7516 () Distance BE 7inch Distance EA 4.5 inch Distance AV : 3.sinch Ay 6) 7516 マへ