10 20 15 10 (volts) S Voltage O S -10 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 -15 -20 20 Time (sec) Based on the AC waveform shown above, what is the maximum voltage the average voltage ' the VRMS (root mean square voltage) , and the period , full width-half max rise time fall time ?

10 20 15 10 (volts) S Voltage O S -10 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 -15 -20 20 Time (sec) Based on the AC waveform shown above, what is the maximum voltage the average voltage ' the VRMS (root mean square voltage) , and the period , full width-half max rise time fall time ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

An ac resistance is higher than a dc resistance. True False
1. Impedance is the total opposition to an AC circuit caused by electric penalty tions, the tra capa multiple pacitive systema 62 Fundamentals of AC Electricity Questions for This C a. 1. Draw a diagram of an AC sine wave and identify its peak voltage and peak-to-peak voltage levels. b. 2. Explain the term frequency as it refers to AC electricity. c. 3. Discuss the difference between a load center and a fused disconnect. 2. WE wa 4. Explain how you would test for voltage in a fusible dis- connect on the line-side and load-side terminals. vi ci 5. Trace the path of a generated AC voltage from the generat- ing station where it is produced to the point where you would connect it to a machine in a factory. Be sure to iden- tify all the important parts of the system between the gen- eration station and the disconnect on the machine. a. be 3. True or False inductive reactance, capacitive reactance, and resistan 2. The units of impedance are
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
LVDT produces an rms output voltage of 5.0 V for displacement of 3.5 mm. Calculate the sensitivity of LVDT please explain me
POWER SISTEMS high voltage technlque it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approxlmate pulse voltage for pulse hlgh voltage , approxlmate voltage value for DC voltage , AND effective value for AC VOLTAGE voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE THREE EQUESTION AND THE OPTIONS ARE THE SAME approxlmate pulse voltage for pulse hlgh voltage, approxlmate voltage value for DC voltage , AND effective value for AC VOLTAGE
DC-AC Circuits Approximately, how long does it take the circuit to have a current near 5A upon closing of the switch? 5V 5H O A. 25 seconds B. 5 seconds O C. 1 second D. O second O E. 0.2 seconds
ssignment_2 5 Immersive Reader O Open in Deskt (b) Connected in paralld. 7) The following readings are obtained in the measurement of an inductor: 1.003,0.998, 1.001, 0.991, 1.009, 0.986, 1.005,0.997, 1.008, and 0.994 µH. Determine the (a) Arithmetic mean. (b) Average deviation. (c) Standard deviation.
Explain the concept of power quality in electrical systems and the potential issues that can arise, such as voltage sags, harmonics, and flicker.
is the simplest way of producing a source of lower EME from a source of higher EMF.
multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -
The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
How much voltage is taken by capacitor #4 (c4)? Select one: a. 7.2 volts b. 6.36 volts c. 5.65 volts d. 4.8 volts