1.2x 10-in. Undeformed Deformed EXAMPLE: 6. An initially rectangular element of material is deformed as shown in the figure (note that the shearing strain is greatly exaggerated). Calculate the normal strain Ex and Ey, and the shear strain for the element. (Practice at Home) B -1.5x10-in. 0.2 in. 0.25 in. 0.7x 10 in. C L 1.8 x 10-in.

1.2x 10-in. Undeformed Deformed EXAMPLE: 6. An initially rectangular element of material is deformed as shown in the figure (note that the shearing strain is greatly exaggerated). Calculate the normal strain Ex and Ey, and the shear strain for the element. (Practice at Home) B -1.5x10-in. 0.2 in. 0.25 in. 0.7x 10 in. C L 1.8 x 10-in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.8P: A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer...

See similar textbooks

Similar questions

A stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram below. The initial sample diameter is 0.502”, the diameter of the fractured sample is 0.412”, the original gage length is 2.00” and the final length after fracture is 2.78”. Determine/ calculate the following: (a) The stress at the proportional limit. (b) The modulus of elasticity (E). (c) The yield stress using the 0.2% offset method. (d) Theultimatetensilestrength. (e) The rupture stress. (f) The percent reduction in area. (g) The percent elongation. (h) Is the material considered ductile or brittle?
Project 2: 40-mm sides glass polymer fibers composite cube is shown in Figure.1. The Glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to a compression load of 65 kN in the x direction. Estimate the strain, change in length and stresses in x,y, and z directions as well as determine the volumetric strain. Illustrate the effect of two and three-dimensions by constructing appropriate sketches. If the cube is only constrained against deformations in the y direction, describe the changes in two and three-dimensions by constructing appropriate sketches. E,= 50 GPa E, = 15.2 GPa v = 0.254 15.2 GPa =0.254 %3D 0.42S
In lab tests on a brick whose dimension are shown in the figure to the right, a force of 1500 N directed at 9.00° above the horizontal is applied on both the lower and upper faces of the brick causing the vertical side of the brick to deform through an angle of 1.25º. (a) How much shear stress is applied on the upper and bottom surfaces of brick? (b) What is the shear modulus of the brick? 9.00° 10 сm 25 cm 3-dimensional view 25 cm Front view after Before applying stress applying stress 10 cm 1.25°
1.7C1 1.4C1 ci 0.9C1 Uniform plastic elongation Necking Elastie 0 4 % 15% 35% Strain in % Stress-Strain diagram Stress in MPa
1.2 x 10-in. Undeformed Deformed B An initially rectangular element of material is deformed as shown in the figure (note that the shearing strain is greatly exaggerated). Calculate the normal strain Ex and Ey, and the shear strain for the element. +1.5 x 10-in. 0.2 in. 0.25 in. 0.7 x 104 in. C X 1.8 × 10-4 in. X
Derive the following equation for computing shear stress in a solid bar along an oblique plane with angle B with respect to the vertical plane. The bar is subjected to centric axial loading. sin 0 cos 0 T = Ao
Problem 2.11 3 of 7 > I Review Part A The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L= 450 mm, H= 345 mm, di = 3 mm, d2 = 5 mm, dz = 11 mm, d4 = 9 mm, d, =1 mm, and d6 = 4 mm. Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. μΑ ? (Yc)ry = Value Units Submit Request Answer Figure 1 of 1 Part B dz Determine the shear strain Yry at corner D d. Express your answer to three significant figures and include appropriate units. di B μΑ ? H (YD)zy = Value Units L d. Submit Request Answer P Pearson
With a thick walled cyclinder the inner radius is 0.05m and out radius is 0.2m. The internal pressure is 200 MPa - What is the hoop and radial stress at the inner surface? - What would be a suitaable material for the cyclinder under von mises criterion?
1. Define the Kinematic Analysis, 2. What are the fundamental structures? Give an example for each one. 3. Define the Strain and write its formula? and briefly explain the types of strain? 4. Draw one or several diagram(s) to illustrate the terms: fold wavelength, fold amplitude, hinge line, axial plane. 5. Draw one or two diagram(s) to illustrate the difference between buckling by flexural shear and orthogonal flexure. 6. How would you explain the differences between thrust fault and Reverse faults? Are their kinematics in any way similar to Normal faulting and Strike Slip? 245 Cuう
If the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original length and the original diameter if the length and diameter under load are 2.333 ft. and 1.005 in. respectively.
A 3-mm-long gold alloy wire intended to electricallybond a computer chip to its package has an initial diameter of30 μm. During testing, it is pulled axially with a load of 15grams-force. If the wire diameter decreases uniformly to29 μm, compute the following:a. The final length of the wire.b. The true stress and true strain at this load.c. The engineering stress and strain at this load.
5b.You used a material to design a system. The more you apply external force, the more the system becomes rigid. Use a sketch to explain how the material is disobeying the stress and strain characteristics. Give two(2) examples.