Using Three-Moment equation, determine the reaction of the supports at point B and C.Possible Answers:By=22657/544 lb (upward)Cy= 9973/272 lb (upward) 1. Using Three-Moment equation, determine the reaction of the supports at point Band č.Answers: B, =22657Elb ↑ & Cy =9973lb 127254410 Nm50 NEIISCONSTAN

First, we will analyze the span ABC Three-moment equation for span ABC :…

Answered: 1. Using Three-Moment equation,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3: Analysis the structure shown in figure, El is constant W=20 KN/m P-40 KN B4 4m
Determine the reactions at the roller B, the rocker C, and where the beam contacts the smooth plane at A. Neglect the thickness of the beam. Suppose that F₁ = 450 N and F₂ = 720 N (Figure 1). Figure R -2 m- 608 5 m < 1 of 1 ▼ Determine the magnitude of the reaction at A. Express your answer to three significant figures and include the appropriate units. FA= Submit Part B (FB)y= O Submit μA Value Request Answer Determine the y component of the reaction at roller B. Express your answer to three significant figures and include the appropriate units. μA Value Units Request Answer ? Units ?
Consider the construction shown in the figure below. The supports at A and C are flexible and have a stiffness k. The material has a modulus of elasticity of E. (Figure 1) Part A Determine the support reaction at A Express your answer in terms of r and some or all of the variables k, a, d. P, and E. nν ΑΣφ ? vec FA = Figure < 1 of 1 Submit Request Answer Part B Determine the support reaction at C. Express your answer in terms of r and some or all of the variables k, a, d, P, and E. |B If vec 2a a Fc =
(b) (5 pt) Draw and properly label a free-body diagram of ring A of the structure shown. Include only relevant information; do not include any information that is not relevant to the free-body diagram. Note: Assume the ring at A is massless. 3 m 3 m wwww kac = 20 N/m 4 m KAB = 30 N/m www. KAD = 40 N/m B
A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar element by i) ii) A Determining the reactions at either ends. Determining the reactions at either ends when the joint C is reduced by 'u' mm from wall/constraint joint C. 0.7 L Figure 1 0.5 L U
A beam shown has the following loads Calculate the values of reactions in kN By in kN Ay in kN Ax in kN
The ratio of reactions Ra and Rgof the simply supported beam, as shown in figure below, will be 5t 3t 2t/m A. B E R, R, - 2 m 2 m 2 m 2 m
Q.4.b. A compound bar is made up by connecting a steel member and a copper member rigidly fixed at their ends as shown in figure below. The cross sectional area of the copper member is A while that of the steel member is 2A for half the length and A for the other half of the length. The coefficient of expansion for steel and copper are as-11.7*10ºC and a=17*10-/C respectively while the modulus of elasticity are E,=210Mpa and E=105MPA respectively. Estimate the stress induced in the members due to rise of 500 in temperature. 2A Steel Copper
Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 т B 50° A
b) A cylindrical rod AB is made of aluminum is connected at B to a brass qylindrical rod BCD as shown in Figure 8. The shear modulus, G of aluminum rod AB is given by 27 GPa and the brass rod BCD of 39 GPa. The torsional reactions, TA and Ts are located at the ends of A and B, respectively. Given the portion CD of the brass rod is hollow and has an inner diameter of 40 mm, examine the angle of twist at A. 60 mm Tg = 1600 N - m 36 mm TA = 800 N m 250 mm 375 mm A 400 mm Figure 8
D 140 mm in the trusses analyies experiment we got the strain Reading as, B Loaden) 5train AB strain AC 5train BC (EM) (EM) (EM) O 469 1117 1116 50 465 1115 1126 100 463 1110 1131 150 458 1095 1139 200 453 1085 250 450 1080 calcute the force in each member; F= πTd²x ExE 4 d = 5.985mm E = 210 GN/m² B W с 1148 t 155
A compound beam as shown with a pin at A, a hinge at C, and rollers at B and D,1) Draw all F.B.D.s for your calculation;2) Determine the reactions at A, B and D when the beam is in equlibrium [Hint: 1) ABC part is the independent part and CD is the dependent part of the compound beam. The analysis always starts from the dependent part, then the independent part. 2) Draw the FBD of CD part first.]

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. Using Three-Moment equation, determine the reaction of the supports at point B and č. Answers: B, 22657 9973 Elb ↑ & C, = tb ↑ 544 272 10 m 50 IN EISCONSTANE