1. Is external force present to influence the analysis? Yes or No? 2. If the solvent is chloroform, which of the pigments is polar and non polar? 3. Compute the retention factor of the blue pigment. 4. Which of the pigments has the highest retention factor 5. What does a high retention factor imply in the analysis? The pigment of interest is well carried by the mobile phase. The pigment of interest is highly attracted to the stationary phase. The mobile phase is not suitable for extracting what is desired. The stationary phase warrants modification.

1. Is external force present to influence the analysis? Yes or No? 2. If the solvent is chloroform, which of the pigments is polar and non polar? 3. Compute the retention factor of the blue pigment. 4. Which of the pigments has the highest retention factor 5. What does a high retention factor imply in the analysis? The pigment of interest is well carried by the mobile phase. The pigment of interest is highly attracted to the stationary phase. The mobile phase is not suitable for extracting what is desired. The stationary phase warrants modification.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What is the best Chromatography instrument for analysis of Soluble Protein molecules CG-FID GC-MS LC-MS IC-MS O IC-EC
Determine the Kovats retention index for an unknown C9 sample using the retention times 1.3 min for benzene, 16.4 min for p-xylene, 18.7 min for the unknown C9 sample, and 20.4 min for p-divinyl benzene. Question 1 options: 864.862 846.801 892.106 920.663
In RPLC, The retention of a basic analyte in RPLC decreases as the mobile phase pH increases. True or False?
Table 1: Selected phytocomponents identified in the plant extract. Retention time, min Name of Compound 10.767 Benzaldehyde 15.790 Azulene 16.002 1-Piperazinecarboxaldehyde 17.935 Phthalan 20.731 2-methoxy-1,3,4-trimethybenzene 24.028 Methylesterpentanoic acid 26.993 Tetradecamethylcycloheptasiloxane 31.753 Hexadecamethyl Cyclooctasiloxane If GC is combined with MS, what data you will add as the 3rd column in Table 1 above. Fill in that data for each of the select identified phytocomponents.
b. Our ability to separate compounds like the four above are dependent on the properties of the column. Using the data from a 250 mm column shown below, please calculate the retention factor for compound A, the number of theoretical plates for compound C and the plate height for compound C. compoun t, (min) w (min) tm 5.04 0.10 A 7.10 0.16 В 7.15 0.17 7.23 0.16 c. Do you want a large or small number of theoretical plates? In no more than two sentences, explain why.
▪ In a blood alcohol analysis by GC-FID, methanol elutes at 1 min, ethanol at 2 min, IPA at 3 min, and IS at 4 min. In the patient sample, the analyte elutes t 2 min and the IS at 8 min. What is the relative retention time and the analyte in the patient? ▪ A) methanol B) Ethanol ▪ C) IPA
29. What exactly is relative retention and retention time? How do you solve problems like this?
The figure below shows a typical separation of several fat-soluble vitamins by HPLC. The x-axis is retention time in minutes. From the graph try to estimate retention times for peaks 2 and 3. Retention time peak 2 = Retention time peak 3 = Assume that w1/2 is 0.15 minutes for peak 2 and 0.16 minutes for peak 3. Assume that tm is 2.00 minutes. How much time does gamma-tocopherol spend in the stationary phase? From tr and w1/2 find N for the peak that elutes first. From tr and w1/2 find the resolution of peaks 2 and 3 Calculate α for these peaks. If the flow rate for the column is 1.2 mL/minute what is the retention volume for peak 4?
In the table below, record the color that you observe for each spot or component of each spot after the run is completed. For the retention factor, R₁, write in the numerator (top) the number of mm that the spot has moved and in the denominator (bottom) the number of mm that the solvent has moved from the point where the samples were 'spotted. Calculate the Rf vale for each spot or component of each spot. Im having a difficult time finding the Retention Factor for M&Ms by using Salt water and seeing how much each color moves Instructions Coffee filters usually are round, but it's easier to compare your results if the paper is rectangular. So, your first task is to cut the coffee filter into a rectangle. Measure and cut a 2-3/4" by 7" strip from the middle of a coffee filter. This is easily done by folding the filter in half (to make a half-circle) and then folding the half-circle into thirds. Cut along the 13-fold lines and trim the ends to make a rectangle. 2. Using a pencil (ink from…
The surface of the silica gel has a structure that looks like this diagram below. Suppose you used a plate coated with silica gel, with propanone, CH3COCH3, as the solvent for thin-layer chromatography. Sno Suppose also that the mixture you were trying to identify contained • benzaldehyde •benzanilide • phenol 1) rank the Rf Value from large to small 2) name the IMF between each compound and the silica gel OH OH main body of silica structure
Explain the reactions involved in separation separation of benzoic acid from mixture contain 3 components 1.Benzoic acid (acidic nature pKa=4.17) 2.Naphthalene (neutral compound) 3.paraNitroaniline(basic compound pKa=12.99
In a chromatographic analysis of low-molecular-weight acids, butyric acid elutes with a retention time of 7.63 min. The column's void time is 0.31 min. Calculate the retention factor for butyric acid