1. Consider an RLC (Resistor-Inductor-Capacitor) circuit supplied by a 20V RMS, 60Hz source as shown. If the following values apply to this circuit: R = 1000 ohm, L = 2.5H, C = 300 nF, find: Total Impedance of the circuit Total Current supplied by the source Current at the capacitor Total Apparent Power of the circuit a. b. C. d. Reactive Power consumed of the capacitor Reactive Power consumed by the inductor g. Power factor of the system? Is the network resistive, inductive, or capacitive? e. f.

1. Consider an RLC (Resistor-Inductor-Capacitor) circuit supplied by a 20V RMS, 60Hz source as shown. If the following values apply to this circuit: R = 1000 ohm, L = 2.5H, C = 300 nF, find: Total Impedance of the circuit Total Current supplied by the source Current at the capacitor Total Apparent Power of the circuit a. b. C. d. Reactive Power consumed of the capacitor Reactive Power consumed by the inductor g. Power factor of the system? Is the network resistive, inductive, or capacitive? e. f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
Draw the phasor diagram for both series and parallel RLC circuits in parts (i) and (ii). Discuss the effects of changing the capacitor connection in parallel on the power factor of the circuit.
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
4. a. Design a combination of at least one resistor, one inductor, and one capacitor in series to create an equivalent impedance of 300-j400 Q at a frequency of 10,000 rad/s. (Note that there are many potential solutions to this problem.) b. At what frequency does the circuit from part a) have an impedance that is purely resistive?
A capacitor C is connected in series with a 400 resistor across a supply of frequency 60 Hz. A current of 3 A flows and the circuit impedance is 500. Calculate: (a) the value of capacitance, C, (b) the supply voltage, (c) the phase angle between the supply voltage and current, (d) the p.d. across the resistor, and (e) the p.d. across the capacitor. Draw the Phasor diagram.
9. What will be the impedance of a LR-C circuit if it has a circuit current of 3A and a supply voltage of 120V? A. 45ohm B. 50 ohm C. 40 ohm D. 35 ohm 10. A pure inductance of 100mH is connected in parallel to a 25microfarad capacitor. The network is connected to a 200V, 60Hz supply. Determine the circuits current. A. 2A B. 3.42A C. 4A D. 10A
An A.C Bridge as shown in the figure is used to measure unknown inductance L1. in companion with capacitance What would be the quality factor if the frequency is 1500 Hz & the various parameter are as below- 120V
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
An inductive coil of resistance 15 ohms and inductance 0.2H is connected in parallel with a 100 micro farad capacitor to a variable frequency supply. Find the frequency at which the total current taken is in phase with the supply voltage. What is this value of this current if the voltage is 200v. Draw a phase diagram
A circuit consisting of a resistor in series with a capacitor takes 100 watts at a power factor of 0.5 form a 100 V, 60 Hz supply. Find the current, resistance, the impedance and the capacitance.